Digital Flow Switch (Remote type sensor unit) Rated flow range [L/min] Model Min. Max.
S 1 0.53 28 2.511 48 418 6.531.5 6.531.5 10 FKM1.310 3/s Pam -11 FKM1.310 KFNW KFNW KDN SUS316L,SUS304,FKM 2 MPa G 0.40.7[ ] 46 200 360 660 1350 3000 5150 3 3 cm O.5MPa 2.5 12 15.5 30 42 54 54 M5 Rc1/8 Rc1/4 [kg] 0.5 1.2 1.8 3.4 5.6 11.5 20 1 2 [Y-VAC2] 5 3 1 1mm 32 L/SP=0.1MPa 30 6 P11) 28 XLD-100 XLD-160 L/s () P=0.1MPa 26 24 22 20 XLD-63 XLD-80 18 16 14 XLD-50 12 10
MGP M 25 30 M9BW M L A S 2 S 1 n n ( 12 12mm 40 40mm 16 16mm 50 50mm 20 20mm 63 63mm 25 25mm 80 80mm 32 32mm 100 100mm A (MGPM,L,A 16100) M5X0.8 Rc N NPT TF G (mm) 2. (mm) MGP12,16,20,25,32,40,50,63,80,100 MGP-A 16,20,25,32,40,50,63,80,100 MGPS50,80 3.
Measures should be taken to protect against human injury and machinery damage in the event that there is a loss of air pressure, electricity or hydraulic power. l. Condition that the products are deformed by force or weight applied. 2. Do not close any objects which are affected by magnets.
H H H Gripping point Gripping point L L Gripping point L "L" and "H" are appropriate "L" is too long "H" is too long 2. Attachments should be designed to be as light and short as possible (1) A long or heavy attachment increases the inertia force required to open or close the fingers.
Amount of grease Piston rod L Fully extend the piston rod L=10 to 15mm (per 100mm of piston stroke) e.g.) For 200mm stroke, L = 20 to 30mm * Apply grease evenly over the piston rod base. Grease package No. GR-S-010 (10g) GR-S-020 (20g) After applying grease, operate the piston rod 2 to 3 times to spread the grease evenly over the full stroke of the piston rod. 2.
Table. 11-1 Length the EX245 series module n 0 1 2 3 4 5 6 7 8 L 113.6 167.6 221.6 275.6 329.6 383.6 437.6 491.6 545.6 Formulas: L = 54n + 113.6 (max. 8 modules) (Dimensions in mm) -57No.EX##-OMU0020-A 12. Troubleshooting 12.1. EX245-SPN1/SPN2 Table. 12-1 Troubleshooting for bus communication No. Problem Possible cause Remedy 1 LINK indicator is OFF.
MHT2-32D L = 100 mm Gripping force (N) Gripping force (N) Gripping force (N) Gripping force (N) MHZ Pressure 0.6 MPa MHF 0.4 MPa 0.2 MPa L Gripping point distance (mm) MHL Opening/Closing angle (Both sides) MHR MHT2-40D L = 120 mm MHK MHS MHC Indication of effective gripping force The effective gripping force shown in the graphs to the right is expressed as F , which is the thrust of one
Auto switch Cylinder B Cylinder A CUJ cylinder Auto switch Magnetic substance Non-magnetic spacer of 2.5mm or more Without shielding plate d 10 L 6 8 Bore L d 19 6 19 6 19.5 6 The space can be reduced by attaching shielding plates (steel plates 0.2 to 0.3mm thick) to the sides of the cylinders facing each other.
min (ANR) Effective area (mm2) Flow rate l/min (ANR) Flow rate l/min (ANR) Number of needle rotations Number of needle rotations Number of needle rotations Inlet pressure: 0.5 MPa Inlet pressure: 0.5 MPa Inlet pressure: 0.5 MPa Effective area (mm2) Flow rate l/min (ANR) Effective area (mm2) Flow rate l/min (ANR) Effective area (mm2) Flow rate l/min (ANR) AS Number of needle rotations Number
MHT2-32D L = 100 mm Gripping force (N) Gripping force (N) Gripping force (N) Gripping force (N) MHZ Pressure 0.6 MPa MHF 0.4 MPa 0.2 MPa L Gripping point distance (mm) MHL Opening/Closing angle (Both sides) MHR MHT2-40D L = 120 mm MHK Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Particle density for particle of 0.3m or larger is less than 3.5 particles/l Since it is possible to release exhaust air from pneumatic equipment directly into a clean room, piping to exhaust ducts is unnecessary.