Mechanically Jointed Rodless Cylinder with Brake, Hy-rodless Cylinder Series ML1C ø25, ø32, ø40 1 Set the supply pressure at 0.25 to 0.5 MPa. If setting at less than 0.25 MPa, malfunction of the release brake may occur. If line pressure is used directly as supply pressure, any fluctuation in pressure will appear in the form of changes in cylinder characteristics.
Set the supply pressure at 0.25 to 0.5 MPa. If setting at less than 0.25 MPa, malfunction of the release brake may occur. If line pressure is used directly as supply pressure, any fluctuation in pressure will appear in the form of changes in cylinder characteristics.
Item Description Default setting Supply pilot valve at signal ON Sets the ON point of the supply pilot valve signal 5 kPa(H_2) Supply pilot valve at signal OFF Sets the OFF point of the supply pilot valve signal 0 kPa(H_3) Set the range in which the supply pilot valve input is prohibited Sets the range where the ON point of the supply pilot valve signal is not allowed to be input. 1 kPa(H
Press the and buttons simultaneously for at least 3 seconds. Lock out is released. During malfunction lockout is released automatically. Press the and buttons simultaneously for at least 3 seconds. Display starts to blink. Press the button "R" for at least 2 seconds but no longer than 3 seconds. This clears the auto shift function.
Coil (coil in A side) of the single solenoid valve and the speed controller in the opposite side at the rod extended when energized control the extending speed at meter-out and the retracting speed at meter-in. Refer to Fig. (3).
The higher the value is set, the quicker it stops. < [A] Pushing force> Pushing force ratio is defined. < [A] Trigger LV> The condition at which [INP] output signal is turned on. Set it at the value equivalent to the pushing force or less. The [INP] output signal is given when the target force (Trigger LV) is achieved.
Connector CL Note Description Part no. 4 3 2 1 Connector 4 pcs. per set ZS-26-E Sensor cable Cable length: 3 m ZS-26-F Note) At the factory, the connector is not connected to the cable, but packed together with it for shipment. Cable length: 3 m Connector + Sensor cable ZS-26-G The connector is not connected to the cable at the time of shipment.
Tubing piping capacity Piping capacity from ejector and switching valve at vacuum pump to pad can be found from selection graph (3). 3.
(Values at the initial period) Vibration resistance: No malfunction occurred in a one-sweep test between 45 and 2000 Hz. Test was performed at both energized energized states in the axial direction and at the right angles to the main valve and armature.
Lead wire length Nil 0.6 m Example) ZSE1-00-15CN-X129 ZS-20-5A-50 1 pc. 1 pc. 30 3 m 50 5 m 13-8-8 9 Ejector Valve Unit Series ZYY/ZYX How to Set the Pressure How to Use the Connector Hysteresis Hysteresis is the difference between the pressure at which the output signal turns ON and the pressure at which it turns OFF. It turns ON at the set pressure. 1.
Mounting brackets are not mounted and are supplied loose at the time of shipment. Auto switches are not mounted and are supplied loose at the time of shipment. Note) Please also confirm whether the selected auto switch can be mounted at the desired position.
(Values at the initial period) Vibration resistance: No malfunction occurred in a one-sweep test between 45 and 2000 Hz. Test was performed at both energized and de-energized states in the axial direction and at the right angles to the main valve and armature.
(Values at the initial period) Vibration resistance: No malfunction occurred in a one-sweep test between 45 and 2000 Hz. Test was performed at both energized energized states in the axial direction and at the right angles to the main valve and armature.
Auto switches are not mounted and are supplied loose at the time of shipment (Except D-P5DWL). Mounting brackets are not mounted and are supplied loose at the time of shipment. Refer to "Standard Stroke" on page 10-4-6.
Allow at least 0.5 seconds from a locked stop (intermediate stop of the cylinder) until release of the lock. When the locked stop time is too short, the piston rod (and load) may lurch at a speed greater than the control speed of the speed controller. 5.
Vespel is a registered trademark of DuPont. 23
RHC Air balance Supply pressure OSet the supply pressure at 0.25 to 0.5MPa. If setting at less than 0.25 MPa. malfunction of the release brake may occur. OIf air is directly supplied from main line, pressure fluctuation on the main line will directly influence to cylinder operation characteristics.
(Values at the initial period) Vibration resistance: No malfunction occurred in a one-sweep test between 45 and 2000 Hz. Test was performed at both energized and deenergized states in the axial direction and at the right angles to the main valve and armature.
/Stored: 35 to 85% RH (No condensation) Resistance Withstand voltage 250 VAC for 1 minute between live parts and case Insulation resistance 50 M between live parts and case (at 50 VDC) 10 to 150 Hz at whichever is smaller of 1.5 mm amplitude or 20 m/s2 acceleration, Vibration resistance in X, Y, Z directions, for 2 hours each (De-energized) 500 m/s2 in X, Y, Z directions, 3 times each (De-energized
Rod End 1000 100 100 85 80 67 Allowable lateral load at rod end [N] 63 56 50 45 40 100 85 100 Load mass [kg] 80 67 10 32 63 40 56 50 45 40 10 32 3 1 500 300 100 50 500 200 100 400 300 0 Maximum speed [mm/s] Cylinder stroke [mm] Example) Load limit at rod end when the air cylinder 50 is actuated at 300 mm/s.