Air Cylinder NCA1 Series Male Rod End F . Female Rod End B .
WH BZ I E 0 0.05 H1 TA 4-TC TB AL A K F H C0. 1 C0. 1 NA BC 8-J BN S + Stroke F ZZ + Stroke e 8 f l ZZ + l + Stroke h + l With rod boot (mm) Stroke range with rod boot Bore size (mm) Stroke range without rod boot Standard Long stroke 20 25 32 40 A AL B1 BC BN BP BZ C D E F GA GB GC GK GL GR GQ H1 I Standard Long stroke 5.5 6 20 to 200 18 15.5 13 38 93 1/8 14 8 12 2 87 10 (12) 18 4 5 26 to
mounting range GB A F K BN Rc(PT) P TB AL 2-TDe8 (pin O.D.)
H A F K Rc P TS TR CNG Bracket mounting range BN GB AL TA 2-TDe8 (Pin O.D.)
Please contact SMC regarding the bowl assembly supply for psi and F unit specifications.
safety margin of a=4, which allows for impacts that occur during normal transportation, etc. 2 x F > mg Number of fingers When = 0.2 When = 0.1 mg F = x 4 2 x 0.2 and therefore, mg F > 2 x mg F = x 4 2 x 0.1 = 10 x mg = 20 x mg With "a" representing the extra margin, F is determined by the following formula: 10 x work piece weight 20 x work piece weight Note) Even in cases where the
The values in these tables indicate the maximum stroke that can be used in a situation when air is being supplied while the cylinder is stopped in an intermediate position by a) an external force acting on Series CHN Stroke range limit charts: Bore size 20, 25, 32, 40 Symbol Mounting orientation Symbol Mounting orientation Symbol Mounting orientation Symbol Mounting orientation F F F F F
Movement Load : Angular acceleration F: Pressing force (N) T f = F x l (Nm) . 2 = (rad/s 2) Load Static torque calculation t 2 g = 9.8 m/s2 Ts = F x l (Nm) l : Rotation angle (rad) Lever t : Rotation time (S) Axis Rotary actuator Axis Allowable Load Application of the load on the axial direction is tolerated if no dynamic load is generated and the values are within what is shown in the
Movement Load : Angular acceleration F: Pressing force (N) T f = F x l (Nm) . 2 = (rad/s 2) Load Static torque calculation t 2 g = 9.8 m/s2 Ts = F x l (Nm) l : Rotation angle (rad) Lever t : Rotation time (S) Axis Rotary actuator Axis Allowable Load Application of the load on the axial direction is tolerated if no dynamic load is generated and the values are within what is shown in the
Movement Load : Angular acceleration F: Pressing force (N) T f = F x l (Nm) . 2 = (rad/s 2) Load Static torque calculation t 2 g = 9.8 m/s2 Ts = F x l (Nm) l : Rotation angle (rad) Lever t : Rotation time (S) Axis Rotary actuator Axis Allowable Load Application of the load on the axial direction is tolerated if no dynamic load is generated and the values are within what is shown in the
Bore6:CO.5 ~ .+~ MM 4>1O, 1S:Cl n\ ~I +I." ~\ 10>1 f!-f.F F ", "I , H I' f.'5., I1tJ F E Rod end without ~ H S R thread , I Z oG H K l MM 1 s I z..q sst I lost IS" , 5" 16!J. IS'" IN 1 5" lOst ~ 15s1 ' A ... B C E F 15 12 ' 27 31 7 16.5 22.5 29 19 14 4.2 M5 x O.8 i M22 x 1.5 I 20 23.5 29.5 36 5 , 37.5 43.5 50 ' 6 'a~e size ' .rom) .
Thread type Rc Nil Control equipment Symbol A Nil AP M MP F G C E NPTF T G F Air filter with auto-drain Air filter with manual drain Regulator Air release valve Pressure switch Blanking plate (Air release valve) Note) It is not applicable to O n e t o u c h fittings.
*-OMY0008 [F 1] OUT1 OUT1 1. 1. 1. 1.
For pipe thread type F , a G thread conversion fitting set is included.
Head Flange: CG3GN Bore size Stroke With rubber bumper Width across flats KA GA GB 4 x FD 8 x J 2 x P F R0.5 H1 0 E 0.05 MM D FX 0.15 0 E 0.05 I B C Corner of the cover (20 to 63) H A AL Width across flats B1 Width across flats NA F FT C FX 0.15 S + Stroke ZZ + Stroke B End boss is machined on the flange for E.
(Not including sensor accuracy), Response time: 150 ms or less Accuracy (To display value) (25C) 1.0% F .S. or less 1.5% F .S. or less 2.0% F .S. or less PF2 0.5% F .S.
Function selection mode In measurement mode, press the button between 3 and 5 seconds, to display [F 0]. Select to display the function to be changed [F ]. Press and hold the button for 2 Measurement mode Power is supplied. Press the button between 3 and 5 seconds.
Function selection mode In measurement mode, press the button between 3 and 5 seconds, to display [F 0]. Select to display the function to be changed [F ]. Press and hold the button for 2 Measurement mode Power is supplied. Press the button between 3 and 5 seconds.