Turntable Cylinder Series MGT Use a contact protection box in cases such as with an induction load, when the lead wire is longer than 5m or with 100VAC. 1 Operating load is an induction load. 2 Wiring to the load is 5m or longer. Contact protection box internal circuits 3 Load voltage is 100VAC. CD-P11 Use a contact protection box in any of the above listed situations.
element needs cleaning (differential pressure cannot be returned as dust adheres) or an element or a seal needs replacement, clean or replace the element by following the dismantling procedure below. 2-1.
element needs cleaning (differential pressure cannot be returned as dust adheres) or an element or a seal needs replacement, clean or replace the element by following the dismantling procedure below. 2-1.
C 2 m 16-3-20 20 Series PSE Specific Product Precautions 3 Be sure to read before handling. Wiring Caution 3. Connecting to other series Any pressure sensor (SW) can be connected as long as it generates analog output (1 to 5 V) signal. However, the pressure range must match. SMC pressure sensors, Series PSE510 & PSE520, are also connectable.
Stroke 25 36.5 5 22.5 10 14 20 10 20 10 (All dimensions but A and CL are identical to those of the basic style.)
D A protocol that automatically allocates information, necessary to be registered to use the network, such as an IP address, to individual devices connected to the TCP/IP network. DHCP A Dummy Remote can be used to reserve a dummy area within the I/O map.
An injury or failure can result. Load Brown LINE(+) Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use. 20 mm or more Sheath Main circuit + 12 to 24 VDC Do not operate in an atmosphere containing flammable or explosive gases.
L=100mm L=100mm MXP10-10 MXP10-20 MXP10-10 MXP10-20 0.04 0.03 0.08 MXP10-10 MXP10-20 MXP10-10 MXP10-20 MXP10-10 MXP10-20 MXP10-10 MXP10-20 Table deflection (mm) Table deflection (mm) Table deflection (mm) 0.03 0.06 0.02 0.02 0.04 0.01 0.01 0.02 0 0 0 80 20 40 60 80 Load (N) 20 40 60 80 Load (N) 20 40 60 100 Load (N) 12 12 12 L=100mm L=100mm L=100mm MXP12-15 MXP12-25 MXP12-15 MXP12-25 0.05
20 191 11 20 50 98 70 44.5 16 84 11 6.4 117.5 316 3.3 280 46 20 196 20 11 50 70 98 44.5 84 13 11 6.4 117.5 319 3.3 Note 1) For AC20 only, the position of the pressure gauge is above the center of the piping.
As a result, it will not be possible to verify it with the vacuum switch. In such a case, it is necessary to use an ejector that is suited to the nozzle and to select a vacuum switch with a favorable hysteresis and precision. 3.
Also, do not use excessive power supply voltage or superimpose electrical noise such as ripple voltage on the power supply voltage as these could harm the valve. 5. When connecting an induction load such as a circuit protector to the solenoid valve connection, take measures to ensure that the current to the solenoid valve is not reduced too much.
Set the operating pressure using the graphs as a guide.
When removing drain is difficult, use of a filter with an auto drain is recommended. ITVX PVQ VY1 VBA VBAT AP100 3. Piping materials without flexibility such as steel tube piping are prone to be effected by excess moment load and vibration from the piping side. Use flexible tubing in between to avoid such an effect. Caution 1.
Model vEA 250/130 Basic type having driving function only w 251 As a system satety measure, an abnormality detecting circuit is added to vEA 250. l.Command Signal A low power DC voltage controls the outout current. An abnormality detecting circuit and a feedback circuit are added to VEA 250, Use of a sensor gives a wider control range and more precise control. veA252 2.
However, a oreat deal of force will be needed to manually op6ration this valve in order to over@methe mechanical spring as well as the air pressure assisting the spring.
Number of fingers and therefore, mg F 2 x With "a" as the safety margin, F is determined as follows: mg F = x a 2 x When = 0.2 When = 0.1 mg F = x 4 2 x 0.2 mg F = x 4 2 x 0.1 = 10 x mg = 20 x mg 10 x work piece weight 20 x work piece weight (Note) Even in cases where the coefficient of friction is greater than = 0.2, for safety reasons, P/A recommends selecting a gripping force which
The thread size is the same as standard.
Keep the product close to the nozzle as much as possible.
D A protocol that automatically allocates information, necessary to be registered to use the network, such as an IP address, to individual devices connected to the TCP/IP network. DHCP A Dummy slave can be used to reserve a dummy area within the I/O map.
This product operates as a slave. It does not send any requests.