Air Cylinder RSQ Series Stopper Cylinder and J79 Fixed mounrins heisht SefieS RSO Thread mounYboth ends taoDed 1 0 Bore size Q32, #O, 6CIRSnOB32, 40, 50 ' Dire.sioB olfFr ll'a. lle abole a t1e same ds hN u the basic tps (ar th6 bn).
Port size Body size Thread size Thread type Symbol N F Rc NPT G 01 02 03 04 06 10 1/8 1/4 3/8 1/2 3/4 1 An interface part is required if a spacer or spacer with bracket shown in the table below is attached to a modular FRL.
Note 2) For the solenoid valve, use an exhaust center 5 port valve, or a combination of residual exhaust 3 port valve and a pump drive 4 port valve. If air in the drive chamber is not released when the pump is stopped, the diaphragm will be subjected to pressure and its life will be shortened.
Do not operate in an atmosphere containing flammable or explosive gases. Fire or an explosion can result. This product is not designed to be explosion proof. If using the product in an interlocking circuit: Provide a double interlocking system, for example a mechanical system. Check the product regularly for proper operation. Otherwise malfunction can result, causing an accident.
Compact / Lightweight 2 Port Solenoid Valve VDW30/40-XF Series For Air/Water Compact / Lightweight resin body (PPS) IP65 RoHS Weight: 120 g (VDW30-XF) n t r e y l d a i 30 mm c r e i r c e s l t e e c c t b t i Power consumption e e o n d l a n .
Main piping line should have an inclination of 1 cm/m in direction of downstream air. 2. In branching from main piping line, a T joint should be provided on the top of the branch piping to prevent drainage collected inside the piping from flowing out. 3. All lower portions of the piping and free ends should be provided with a draining device to prevent drain accumulation. 4.
Consult with SMC if a different fluid is to be used. Consult SMC regarding products for general purpose fluids, to confirm which fluids may be used. 2. When there is a large amount of drainage Compressed air containing a large amount of drainage may cause malfunction of pneumatic equipment. An air dryer or Drain Catch should be installed upstream from filters. 3.
Using a regulator on the secondary side When mounting a regulator on the secondary side (A port side), use a residual pressure relief regulator (AR2550 to 4050) or a check type regulator (AR2560 to 6060). With a standard regulator (AR1000 to 6000), the secondary side pressure may not be released when this valve is exhausted. 5.
If these items need to be supported, provide an additional support. t A Class 2 Pressure Vessel Pressure Resistance Certificate is provided with those below, which are considered to be Class 2 pressure vessels. Make sure to store the certificate in a safe location.
Use caution, as there is a danger of being burned if a valve is touched directly. 2. Valves may reach high temperatures when continuously energized. Use caution, as there is a danger of being burned if a valve is touched directly. SOL. AC AC SOL. Without light AC SOL.
The maximum protrusion of an auto switch (when fingers are fully closed) from the edge of the body is shown in the table below. Use the table as a guideline for mounting. Auto switch mounting bracket part no. BMG2-012 Auto switch part no. D-M9(V)/M9W(V)/M9A(V) Note) Use a screwdriver with a grip diameter of 5 to 6 mm to tighten the set screws (M2.5).
140.5 LVR50-V19 22 80 120 169 C F E Breathing port M5 x 0.8 J Tube extensions 4 x 7 Mounting hole 1/8 (Rc, NPT) Pilot port A H D B G Breathing port M5 x 0.8 Model A B C D E LVR20-T07(06) 40 40 49.3 68 20.1 LVR40-T11(10) 82.5 82.5 89 115 33 IN C F Model F G H J K LVR20-T07(06) 8 27 56 33.5 126.2 LVR40-T11(10) 14 64.5 100 40 183.3 E K J J Breathing port M5 x 0.8 5 Applicable Fluids Regulator
Manifold Options JIS symbol Blanking plate assembly VVCW 0 3A 2 A Series Material 2 3 4 Class 2 Class 3 Class 4 Plate material C37 Stainless steel Seal material Symbol A H FKM This is used by mounting it on the manifold block when a valve is removed for maintenance, or when the mounting of an additional valve is planned, 5 Series VCL Direct Operated 2 Port for Oil Dimensions (mm) (N.C.)
Conforming to ISO 16030-2001, the chamfered dimensions shown in the First, tighten it by hand, then give it an additional 1/6 turn to 1/4 turn with a wrench. A reference value for the tightening torque is 1 to 1.5 Nm. Note) Excessive tightening may damage the thread portion or deform the gasket and cause air leakage. table below are recommended.
The life of a buffer will be reduced if the lateral force is applied to the buffer shaft. Note that sometimes a load is applied to the buffer by a piping tube (pulling or pressing, etc. in a lateral direction). 5. Do not apply an impact or large forces to a pad when adsorbing a workpiece. This will cause deformation, cracking and wear of the pad to be accelerated.
Conforming to ISO 16030-2001, the chamfered dimensions shown in the First, tighten it by hand, then give it an additional 1/6 turn to 1/4 turn with a wrench. A reference value for the tightening torque is 1 to 1.5 Nm. Note) Excessive tightening may damage the thread portion or deform the gasket and cause air leakage. table below are recommended.
(With gasket, 2 mounting screws) VC VDW VQ Blanking block assembly (VCA30, 40) VVCA 3 0 2A 00 VX2 VX Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com 3 4 Series VCA30 Series VCA40 VX3 This is used when a blanking plate is mounted on a manifold as preparation for a
water flow of 4l/min at a differential pressure of 0.1MPa, an effective area with Cv factor 0.28 (VDW303) or more is required.
Note 2) The grommet type is equipped with a surge voltage suppressor (direct coupling type lead wire), but not an indicator light.
x 1.25 M10 x 1.5 185 145 95 80 50 40 25 26 M39 x 1.5 40 Note) The pin, keeper plate and cap bolt are included with a double knuckle joint.