Series AV is a soft start up valve for low-speed air supply to gradually raise initial pressure in an air system and for quick exhaust by cutting off air supply.

This is a legacy product. Please contact us for the latest version.sales@ocaire.com, DIGITAL FLOW SWITCH, INSTRUMENTATION, IFW/PFW FLOW SWITCH, DB, IFW/PFW 1/4INCH NPT VERSION, .73323 lb, ModelGas ratioRated flow rangeDisplayable rangeSettable rangeMax. analog output ArCO2Voltage (Vmax)Current (Imax)PFM71192%8%2 to 100 l/min2 to 105 l/min0 to 105 l/min5.00 V20.0 mA

CYL, B, A, 25. 0.65800 lb. 333.

CG1, double acting, single rod cylinder with made-to-order options, Bores sizes *: 20, 25, 32, 40, 50 63 *, Most options are auto switch capable, Available strokes: 25mm to 1500mm depending on bore size, 7 mounting options, CYL, B, A, 80, ROUND BODY CYLINDER, 333, 2.95700 lb

Compact Guide Cylinder End Lock Type SeriesMGP

Z Y69BZ Solid state switches marked with a "p" are produced upon receipt of order. Specifications Lock Specifications Lock position Rear, Front Double acting Action 32 40 50 63 Air Fluid Holding force (max.)

For the old CDM□ series, replace each auto switch with one applicable to the CDM2 □-Z series.
The CM2 series and CDM2-Z series catalogs can be found <a href="/webcatalog/en-jp/seriesList/?type=GUIDE&id=CM2-CDM2-Z-E&show_page=true" target="_blank">herea>.

Title not found

a a a o a o a a a a o a a a a o a a a a a a o a a a i a a a a a a a a a a a a a a a a a a a a a a a a a a a r a a a a a a o a o a SMC Offers the Highest DimensionalAccuracy .

TABLE OF CONTENTS

A valve, which might potentially cause a hum or buzz can be very annoying to a patient, so a full wave rectified unit for AC service is often preferred. A DC unit, not requiring a rectifier, is sometimes used in specific applications. Also common is a bumper in a 2-way valve, usually just a flat disk with no sealing action.

VQ7-6/7-8

Rc1/4 Rc3/8 Bottom Note) When equipped with control unit, 1 or 2 stations are used for mounting. 6 Series VQ7-6 DIN Connector Type VV71-100 80 2n-Rc1/4, 3/8 100 80 9 37 9 23 14 U side 15 R4.5 Manual override Indicator light R4.5 53.5 P=43 9 9 53.5 P=43 20 9 23 38 B B B B B B B B B SMC SMC SMC A PA PA PA PA A A A A B A L1 L2 L2 L1 B A B SMC A B A 4n-Rc1/4, 3/8 (ports A, B) PA L side R side

AC

As a rule, the electro-pneumatic hybrid regulator should be installed in a location that is free of noise or is shielded. If it must be installed in an environment with poor noise conditions, eliminate the power supply noise by using a line filter, Z-wrap, or a spark killer on the 100V power supply or signal source line.

CLQ

Hs A B A B 32 to 100 D-A73C D-A80C D-J79C D-A79W D-F7WV D-F7V Approx.

Auto Switch Guide

L D-A73 (Example) RS H A Lead wire length RZQ 5 m None Nil L 0.5 m 3 m Z N MI W S Applicable for the connector type (D-C) only.

HRX-OM-W060

For a facility having a small installation area (that can not vent the air naturally): Make a forced air exhaust vent on a wall at a high level and an air inlet on a wall at a low level. 3.

VS 8-2/VS 8-4

Regarding a vacuum switch valve and a vacuum release valve If a non-vacuum valve is installed in the middle of piping system having a vacuum, the vacuum condition will not be maintained. Use a valve designed for use under vacuum condition. 10.

Auto Switch Guide

When a load, such as a relay or solenoid, which generates surge is directly driven, use a type of switch with a built-in surge absorbing element. 8.

Auto Switch Guide

When a load, such as a relay or solenoid, which generates surge is directly driven, use a type of switch with a built-in surge absorbing element. 8.

Note) Even the standard piping type of the MY1B and MY1H series can be changed to a centralized piping type by changing the position of the plug.
However, MY1B-Z and MY1H-Z series cylinders cannot be changed to a centralized piping type.
The MY1B series catalog can be found <a href="/webcatalog/discontinued/detail/en-jp/air-cylinders/MY1B-old-e" target="_blank">herea>.

CRJ

Although a zener diode for surge protection is connected at the output side of a solid state auto switch, damage may still occur if the surge is applied repeatedly. When a load, such as a relay or solenoid, which generates surge is directly driven, use a type of switch with a built-in surge absorbing element. 8.

Series CQ2

Note 2) When mounting a cylinder with a stroke over 100mm, use the section A mounting threads.

VEX1

The poppet valve has a pressure balancing mechanism in which A port pressure is constantly applied from the back and the center spring is acting as a backup.