Electric Actuator / Slider Type 《 AC Servo Motor 》 A C A-A A B B A Auto switch mounting bracket A-A B-B Dust seal band type Seal band holder roller specification C No.
Caution Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Warning Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Danger Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury. Warning 1.
Facility having a small installation area (that can not vent the air naturally) Make a forced air exhaust vent on a wall at a high level and an air vent on a wall at a low level.
9 r e !7 @1 !2 !6 !8 q !1 A B A' B' Without magnet Extension locking u t @5 @0 Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com When shipped Section A-A' Retraction locking !0 !5 Section B-B' !3 !
Facility having a small installation area (that can not vent the air naturally) Make a forced air exhaust vent on a wall at a high level and an air vent on a wall at a low level.
set of a, b, c, d) BMA3-050 (A set of a, b, c, d) BMA3-063 (A set of a, b, c, d) CKQ D-M9ANote 2) BMA3-040S (A set of a, b, c, e) BMA3-050S (A set of a, b, c, e) BMA3-063S (A set of a, b, c, e) Auto switch Switch bracket (Resin) Transparent (Nylon)Note 1) d e White (PBT) c Switch holder b Auto switch mounting screw a * Band (a) is mounted so that the projected part is on the internal side
Air filter (5m or less) When using a solenoid valve, use a metal seal type (series VQ, VQZ, SQ, etc.).
Once in the mounting position, use a flat head watchmakers screwdriver to tighten the included set screw. Note) When tightening the set screw, use a watchmakers' screwdriver with a handle diameter of about 5 to 6 mm.
Applicable bore size (mm) A A1 E1 L1 MM U1 NX NZ L A Applicable bore size (mm) MM R R1 U1 NDH10 NX Applicable pin part no. A1 E1 L1 RR1 Part No.
Vertical Operation 1 2 P2 W A P1 a (b) (a) P0 P0 a A W (1) The speed is controlled with meter-out control. When the meterin controller is used in conjunction with the meter-out controller, lurching is reduced. () (2) Depending on the size pf the load, installing a regulator with check valve at position (a) can decrease lurching during descent, and operation delay during ascent.
Vertical Operation 1 2 P2 W A P1 a (b) (a) P0 P0 a A W (1) The speed is controlled with meter-out control. When the meterin controller is used in conjunction with the meter-out controller, lurching is reduced. () (2) Depending on the size pf the load, installing a regulator with check valve at position (a) can decrease lurching during descent, and operation delay during ascent.
"Jumping" is a condition in which the cylinder operates without control at a speed that is higher than the control speed.
It is dependant upon whether a load is connected with the positive or negative side. These switches are known for high speed response, longevity, and they can reduce wiring work. Voltage drops at the value of r x I. PS1000, PS1100 Caution 1 to 5 [V] Current I Lead wire resistance r The load current range for a PS1000 and PS1100 is between 5 [mA] to 40 [mA].
Therefore, make sure to use a pressure regulator to convert line pressure into supply pressure for the actuating valve and the brake valve. In order to actuate multiple cylinders at once, use a pressure regulator that can handle a large air flow volume and also consider installing a surge tank.
A A B (mm) D-A9V D-A9 D-M9 D-M9W D-M9V D-M9WV A B A B Bore size (mm) W Hs A B W A B Hs 32 40 50 63 12 [17] 9 1 12 [17] 9 29 8 [13] 5 3 (0.5) 8 [13] 5 27 16 11.5 1.5 16 11.5 32.5 12 7.5 5.5 (3) 12 7.5 30.5 14 <19> 14.5 4.5 14 <19> 14.5 42 10 <15> 10.5 8.5 (6) 10 <15> 10.5 36.5 16.5 17.5 7.5 16.5 17.5 42 12.5 13.5 11.5 (9) 12.5 13.5 40 [ ]: Values for 5 mm stroke with 32 < >: Values for 10
When used as a switch output device Setting of NPN open collector 2 outputs Setting of PNP open collector 2 outputs Brown DC(+) q Brown DC(+) q Load Black OUT1 r Black OUT1 r Load Main circuit Main circuit + + 12 to 24 VDC 12 to 24 VDC White OUT2 w White OUT2 w Load Load Blue DC() e Blue DC() e When used as an IO-Link device Brown L+ q L+ Black C/Q r Main circuit C/Q IO-Link master White
Leakage voltage Particularly when using a resistor in parallel with a switching element and using a C-R element (surge voltage suppressor) to protect the switching element, take note that leakage current will flow through the resistor and C-R element, etc., creating a danger that the valve may not shut OFF.
Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Caution: Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Warning: Danger : Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury.
OUT IN BUS COM A COM B COM C COM D F R P B U S O I R DIA BF SOL RUN GATEWAY UNIT EX500 SERIES 18 19 Switch setting Open the station number switch protective cover and set the switches with a sharp-pointed watchmakers screwdriver etc. NOTE 1. Be sure to turn off the power before setting the switches. 2. Be sure to set these switches before use.
When a workpiece could be deformed during adsorption or transportion. (Example of a cardboard box) When the adsorption surface of a workpiece is slanted.