Body Size: 40, Thread: Rc, Port Size: 06 (3/4), Mounting: w/o Mounting Option, Bowl: Polycarbonate Bowl, Lubricant Exhaust Port: w/o Drain Cock, Flow Direction: R (Right to Left), Pressure Unit: Pressure Unit: MPa; Temp Unit: °C

Body Size: 40, Thread: Rc, Port Size: 06 (3/4), Mounting: w/o Mounting Option, Bowl: 2 (Metal Bowl), Lubricant Exhaust Port: w/o Drain Cock, Flow Direction: Left to Right, Pressure Unit: Pressure Unit: MPa; Temp Unit: °C

I/O Configurator (NFC version)

No.EX-OMV0017-A

MY1

Although a zener diode for surge protection is connected at the output side of a solid state auto switch, damage may still occur if a surge is applied repeatedly. When directly driving a load that generates surge, such as a relay or solenoid valve, use a switch with a built-in surge absorbing element. 8.

AC Servo Motor Driver (CC-Link Type)

Reset (RES) Keeping RY(n 1)A or RY(n 3)A (RES) ON for 50ms or longer RY(n 1)A RY(n 3)A 1 allows an alarm to be deactivated. Some alarms cannot be deactivated by Reset RY(n 1)A or RY(n 3)A (RES). (Refer to section 10.4.1.) If RY(n 1)A or RY(n 3)A (RES) is turned ON with no alarm occurring, the base circuit will not be shut off.

HRX-OM-X071

For a facility having a large installation area (that can vent the air naturally): Make an air outlet on a wall at a high level and air inlet on a wall at a low level, to allow for adequate airflow. 2. For a facility having a small installation area (that can not vent the air naturally): Make a forced air exhaust vent on a wall at a high level and an air inlet on a wall at a low level.

AC Servo Motor Driver (CC-Link Type)

Reset (RES) Keeping RY(n 1)A or RY(n 3)A (RES) ON for 50ms or longer RY(n 1)A RY(n 3)A 1 allows an alarm to be deactivated. Some alarms cannot be deactivated by Reset RY(n 1)A or RY(n 3)A (RES). (Refer to section 10.4.1.) If RY(n 1)A or RY(n 3)A (RES) is turned ON with no alarm occurring, the base circuit will not be shut off.

NCA1

Although a zener diode for surge protection is connected at the output side of a solid state auto switch, damage may still occur if the surge is applied repeatedly. When a load, such as a relay or solenoid which generates surge is directly driven, use a type of switch with a built-in surge absorbing element. 8.

AC Servo Motor Driver (MECHATROLINK-III type)

Error Gr.1 A.320 Regenerative Overload Gr.2 A.330 Main Circuit Power Supply Wiring Error Gr.1 A.400 Overvoltage Gr.1 Alarm A.410 Undervoltage Gr.2 A.450 Main-Circuit Capacitor Overvoltage Gr.1 A.510 Overspeed Gr.1 A.511 Overspeed of Encoder Output Pulse Rate Gr.1 A.520 Vibration Alarm Gr.1 A.521 Autotuning Alarm Gr.1 A.710 Overload: High Load Gr.2 A.720 Overload: Low Load Gr.1 A.730 Dynamic

IN20267

Never mount a product in a location that will be used as a foothold. The product may be damaged if excessive force is applied by stepping or climbing onto it. Do not use this cylinder as a stopper. Minimum adjusting stroke necessary for a positioning stop is 5mm. Operate for 5mm or more before a positioning stop. Ex: 1.

Electric Actuator / Slider Type 《 AC Servo Motor 》

A C A-A A B B A Auto switch mounting bracket A-A B-B Dust seal band type Seal band holder roller specification C No.

AC Servo Motor Driver (Pulse input type/Positioning type)

(RES) A.10 Undervoltage A.12 Memory error 1 (RAM) A.13 Clock error A.15 Memory error 2 (EEP-ROM) A.16 Encoder initial communication error1 A.17 Board error A.19 Memory error 3 (Flash-ROM) A.1A Motor combination error A.1C Software combination error A.1E Encoder initial communication error 2 A.1F Encoder initial communication error 3 A.20 Encoder normal communication error 1 A.21 Encoder normal

Fieldbus system EtherNet/IP TM compatible SI Unit IO-Link Master Unit

A 2 A Power supply (Output) 24 VDC +10/-5%, 24 VDC +10/-5%, 8 A DC24 V +10/-5%, 4 A 2 A Enclosure IP67 (With manifold assembled) 1 Environment Operating temperature range -10 to 50 oC Storage temperature range -20 to 60 oC Operating humidity range 35 to 85%R.H.

Fieldbus system Ethernet POWERLINK compatible SI unit

Caution : CAUTION indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Warning : WARNING indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Danger : DANGER indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury.

Digital pressure switch for energy-saving control ejector

due to a new measurement law.

Pressure switch for energy-saving control ejector with N.O. type valve

Check if the load is short circuited. (3) Check if a relay without a surge (3) Use a relay with a surge voltage suppressor or take measures to prevent noise.

Digital pressure switch for energy-saving control ejector

This can be prevented by inserting a noise filter, such as a line noise filter and ferrite core, between the switch-mode power supply and the product, or by using a series power supply instead of a switch-mode power supply.

IDG

When air with high purity is required, please either mount the above separator on the outlet side or use a made-to-order product (refer to page 14-19-50), which is provided with a micro mist separator (Series AWD) instead of a regulator. 3.

I/O Configurator (NFC version)

A wireless slave can then be registered to the dummy area at a later time, without having to change the I/O map Dummy slave E Export Function to save the configured values of a wireless unit by exporting them to a PC. F Fieldbus Network protocol to establish digital communication between an automated industrial system such as a measurement tool or manipulation tool and a PLC.

EXxx-OMW0014CN

OFF 8 V 4 PNP (C/Q) 0.25 A ( US1 ) 57 No.EX-OMW0014CN-A 9.3.