Stainless Steel Heat If abnormalities such as smoke, unusual odor or unusual noise occur, stop the inflow of compressed air, as this may indicate a fire. 2. When performing inspections, set the compressed air pressure at zero.
The Real Time Clock can be used as a power saving device to automatically turn the equipment On/Off at scheduled times.
Piping materials without flexibility such as steel tube piping are prone to be effected by excess moment load and vibration from the piping side. Use flexible tubing in between to avoid such an effect. As a filter is a heavy object, please transfer or install it making sure that it will not be dropped or dented.
Load is an analog input equipment such as a voltmeter.
Note 3) A particulate generation test has been conducted in a vacuum environment of 10-Pa. a t e l u g c 2 Stainless steel linear guide & low particulate generation vacuum grease e i t n r a e p r a 0.0 10 0 20 10 w t i o o n L Operation cycles a t e l u g c e 1 i t n r a e Particulate generation from the linear guide unit has been reduced with the use of a stainless steel linear guide and
This can be prevented by inserting a noise filter, such as a line noise filter and ferrite core, between the switch-mode power supply and the product, or by using a series power supply instead of a switch-mode power supply.
Make sure to clean it once the accumulation of contaminants reaches a thickness of 20 mm or so. w Clean the adsorption surface of the separator by wiping away the accumulated contaminants using a soft rag or the like.
Note) Tighten within the tightening torque of 0.5 Nm 20%. Changing the entry direction The cable entry direction of a connector can be changed as desired (4 directions at 90 intervals), depending on the combination of a housing r and a terminal block e. q r u t y e o i o Magnifying figure Self-up screw 2 1 3 Comparison between the Product Model No. and the Coil Part No.
Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Caution: Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Warning: Danger : Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury.
20 2-M6 thread depth 11 2-M6 thread depth 11 15 15 35 18 15 2-M6 thread depth 11 2-M6 thread depth 11 20 20 A 17 17 40 A 20 20 15 45 60 25 45 60 A Applicable clamp cylinder A Applicable clamp cylinder Part no.
20C (68F) bend the tubing into a U shape.
Note 1) When tightening an auto switch mounting screw, use a watchmakers screwdriver with a grip diameter of 5 to 6 mm. Also, set the tightening torque to be 0.05 to 0.1 Nm. As a guide, turn 90 from the position where it comes to feel tight.
Operating angle Hysteresis angle Model MDSU1, 3 110 10 MDSU7, 20 90 Auto switch Table B port A port Positioning pin hole 11-5-30
A counter clockwise until it stops (approx. 45). 4) Install a new element on cover A and insert it into the case.
After setting the position, tighten the attached switch mounting set screw with a straight bladed watchmakers screwdriver. Auto switch hysteresis is as follows. Please refer to the table as a guide when setting auto switch positions.
This can be prevented by inserting a noise filter, such as a line noise filter and ferrite core, between the switch-mode power supply and the product, or by using a series power supply instead of a switch-mode power supply.
Orifice Fittings Many of our small brass fittings such as B1, B2, T1, T2, etc., are available as orifice fittings. In the case of Tees, the branch and/or one end of the run may be an orifice. A cross can have as many as three orifices. The general dimensions in this catalog are subject to change without notice 5/32 Couplings 7/16 1/2 15/16 1 5/16 5/16 Typ.
Air pressure may not rise with an air compressor of smaU capacity. 8 When source air is very dirty, use a main line filter (Series AFF) as a prefilter. When a reciprocating type compressor is used, use a main line filter(Series AFF) as a prefilter. Use an air compressor with the following capacity: AMH150 AMH650 100.Q.
Modular Type Lubricators Series AL AC-A Lubricator Series AL Model AF-A Port size Option AF-A AL10 M5 x 0.8 AR-A AL20 1/8, 1/4 AL-A AL30 1/4, 3/8 AW-A AL40 1/4, 3/8, 1/2 Bracket AC AL40-06 3/4 AF AL50 3/4, 1 AF AL60 1 Pages 508 through to 513 AR AL AL AW AG E AV AF 507 Lubricator AL10 to AL60 Symbol Lubricator AL20 AL40 How to Order AL 30 03 B Option/Semi-standard: Select one each for a