ZISE3.eng Therefore, do not use it in an environment that is exposed to chemicals such as thinner, carbon tetrachloride, chloroform, acetic ester, aniline, cyclohexane, trichloroethylene, sulfuric acid, lactic acid, or water-soluble cutting oil (alkalinic). Do not use the product in direct sunlight.
This function prevents detection of such temporary drops in the supply pressure as an error. Response time settings: 20 ms, 160 ms, 640 ms, 1280 ms
Manual release bolt Design minimizes influences of unlocking air quality A design largely unaffected by factors such as moisture and condensate in compressed air has been realized by separating the lock mechanism and the brake cylinder. Can be locked in both directions An equal holding force can be obtained on either reciprocating stroke of the cylinder.
It is suitable for use in cases where water must be removed, but the air does not have to be as dry as when an air dryer is used or an air dryer cannot be used because an electric power supply is not available.
an n r tio ta n r Ro +8 0 io Ro tat tat Ro 80 io t 1 n r fla an ge gle of sin +10 0 Ro tat 90 ion t 1 ra fla ng le e o ing f s With external stopper For 90 For 180 Single flat Single flat A n 5 5 gl e ge ge ad an an ju t r t r st en m en en stm m t r st ju ju an ad ad ge le e Ang 5 gl n A B port A port B port A port 90 A 5 n gl ge e an ad t r ju en st m 180 Note) The drawings show
an n r tio ta n r Ro +8 0 io Ro tat tat Ro 80 io t 1 n r fla an ge gle of sin +10 0 Ro tat 90 ion t 1 ra fla ng le e o ing f s With external stopper For 90 For 180 Single flat Single flat A n 5 5 gl e ge ge ad an an ju t r t r st en m en en stm m t r st ju ju an ad ad ge le e Ang 5 gl n A B port A port B port A port 90 A 5 n gl ge e an ad t r ju en st m 180 Note) The drawings show
As a rough guide, tighten the screw an additional 90 after feeling a tight resistance. As a rule, it should be turned about 90 beyond the point at which tightening can be felt. 0.5 0.2 0.3 MHL2-20D 0.5 0.2 0.2 MHC MHL2-25D 0.2 0.1 0.2 MHL2-32D 0.4 0.4 0.7 MHT MHL2-40D 0.2 0.4 0.7 MHY MHW MRHQ Misc.
Using the chewed portion of the tube as it is can cause problems such as leakage or difficulty in removing the tubing. 1. Do not use in a location having an explosive atmosphere. 2. Do not operate in locations where vibration or impact occurs. 3. Do not use in locations where radiated heat will be received from nearby heat sources.
When the SET button is pressed continuously for 4 seconds or more, the display changes as shown in .
If the guide rod has twisted, operation resistance will become abnormally higher and the bearing will wear at an early stage, thereby resulting in poor performance. e Allow an ample space around the cylinder so that no obstruction will occur for checking and maintenance. r Do not adjust the rod stroke by moving the rear plates, as doing so will cause the rear plates to come into direct contact
30 40 With back flow mechanism Note) AW10 comes with a back flow mechanism as a standard feature.
19 1 Communication connector 2 c Cable length: 0.2m 20 View c 315
It turns OFF when an alarm occurs or when JOG movement takes place.
The response time becomes quicker as the set value becomes larger. Additionally, the response time becomes quicker as the piping length becomes shorter.
Also, keep the manual where it can be referred to as necessary. 6. Tighten the nut to the end surface of the body. As a guide, refer to the proper tightening torques shown below.
License Agreement SMC Corporation (hereinafter referred to as "SMC") hereby grants the user (regardless of whether the user is a corporation or an individual) a license to use this software "IP Address Setting Tool" (hereinafter referred to as "Software") according to this License agreement (hereinafter referred to as "Agreement") under the articles listed below.
Caution Mounting 1) Do not subject the gauge to shocks, such as dropping during transportation and mounting, as this can cause loss of indication accuracy. 2) Do not use this gauge in a location with high temperature and humidity, as this may cause faulty operation. 3) When mounting the pressure gauge, be certain to use a wrench on the square wrench flats to screw it into place.
AXT100-20-2-05 AXT100-20-2-06 AXT100-20-2-01 AXT100-20-2-02 AXT100-20-2-03 AXT100-20-2-04 Clip Circuit with light PR plate qChanging the piping direction from in-line to perpendicular (port on the valve) is possible on the VQZ100 series. Follow the steps below to change piping direction: Remove the fitting clips that hold the fitting and port plug in place.
(reference value) 11-LEJS40* Speed 600mm/sec Speed 1200mm/sec 100,000,000 100,000,000 10,000,000 10,000,000 ISOclass8 ISOclass8 0/mi n( AN R ) ISOclass6 1,000,000 1,000,000 ISOclass7 ISOclass7 Particl concentration[Particls/m 3] Particl concentration[Particls/m 3] 100,000 100,000 0/mi n( AN R ) ISOclass6 10,000 10,000 ISOclass5 ISOclass5 50/mi n( AN R ) 20/mi n( AN R ) 1,000 1,000 ISOclass4
T h e V YH y R e g R a n g e i s c o n s t r u c t e d b y u t i l i z i n g a standard control unit either alone (VY1D00-M5) or as a Pilot Valve controlling one of the Range of VEX1 Power Valves.