Microspeed Cylinder dividing the stroke by the piston rod movement time.
(prepared by the user) I/O cable PLC Actuator cable (prepared by the user) Card Motor 24 VDC power supply for the input / output signals Power supply cable (prepared by the user) (prepared by the user) Counter plug (attached to the controller) 24 VDC power supply for the controller Power supply plug (prepared by the (attached to the controller) user) Controller 15 - I/O cable pin assignment
M5: After tightening by hand, tighten an additional 1/6 turn with a tightening tool. However, if miniature fittings are used, tighten an additional 1/4 turn with a tightening tool after tightening by hand. For fittings with gaskets in 2 locations, e.g., universal elbow or universal tee, tighten an additional 1/2 turn.
To operate by applying pressure from the rod cover port: Low friction direction B type (Application example (1)) To operate by applying pressure from the head cover port: Low friction direction F type (Application example (2)) In either case, if the piston rod is moved by an external force, it will operate with low friction for both in the extending and retracting directions. 2.
Simple and unencumbered appearance by adopting roundshaped cord. How to Order 2. Do not use a tool to mount the connector, as this may cause damage. Only tighten by hand. (0.4 to 0.6N) SY100-68-A 3. Do not apply excessive power greater than 30N to the connector cable, otherwise IP65 cannot be satisfied.
Do not carry a cylinder by the auto switch lead wires. Never carry a cylinder by its lead wires. This may not only cause broken lead wires, but it may cause internal elements of the switch to be damaged by the stress. 3. Mount switches using the proper tightening torque. When a switch is tightened beyond the range of tightening torque, the mounting screws or switch may be damaged.
Cuts air consumption by operating the return stroke at a reduced pressure.
Turn another 90 from the position where tightening is felt by hand.
Connectors shape and pin assignment is interchangeable with ET200C made by Siemens AG.
Has large retaining force while holding force is increased by the collet.
Return to the origin position can be done by the [RTN ORIG] button. -27JXC-OMU0010-A 5.4 Teaching method Teaching is a method to set a position by operating the actuator. Teaching method has Jog teaching and Direct teaching. Caution The actuator is operated during teaching.
(Refer to page 56) Level meter: Displays the measured distance (reference) by figure. Display value: Displays the measured distance (reference) by value.
The PB1011A transfers the fluid continuously by suction and discharge in turn by repeating ON/OFF of the built-in solenoid valve. The PB1013A air-operated type is operated by the ON/OFF operation of an external solenoid valve.
a spring force, which is further tilted by the load that is applied to the cylinder, thus locking the piston rod.
the following formula that is based on the test conducted by the test circuit analogous to ISO 6358.
Do not carry a cylinder by the auto switch lead wires. Never carry a cylinder by its lead wires. This may not only cause broken lead wires, but it may cause internal elements of the switch to be damaged by the stress. 3. Mount switches using the proper tightening torque. If a switch is tightened beyond the range of tightening torque, the mounting screws or switch may be damaged.
Do not carry a cylinder by the auto switch lead wires. Never carry a cylinder by its lead wires. This may not only cause broken lead wires, but it may cause internal elements of the switch to be damaged by the stress. 3. Mount switches using the proper tightening torque. When a switch is tightened beyond the range of fastening torque, the mounting screws or switch may be damaged.
Wireless master
Air supply The compressed air supplied to the cylinder should be filtered by SMC AF series air filter and regulated to the specified set pressure by SMC AR series regulator. Warning 1.Use clean air.
Tighten the lock nut on cable side by turning it clockwise by hand. Aligning the key groove with the IN-side communication connector ( 5-pin, plug ) of GW unit, plug the PROFIBUS DP communication cable ( socket ). Confirm that the connector portion does not move.