HRX-OM-X037 The DC power supply has failed. Replace the DC power. The product does not operate after pressing the [ ] button. Communication setting has been turned ON. Check the setting of the operation mode.
4.7k Contact output Rated load voltage AC48V or less/DC30V or less Maximum load current AC/DC 500mA (Resistance load) signal Minimum load current DC5V 10mA DC24V power supply output DC24V10 500mA MAX (No inductive load) 2.3 Terminal block explanation This part explains the terminal block of the contact input/output communication.
4.7k Contact output signal Minimum load current DC5V 10mA Rated load voltage AC48V or less/DC30V or less Maximum load current AC/DC 500mA (Resistance load) DC24V power supply output DC24V10 500mA MAX (No inductive load) 2.3 Terminal block explanation This part explains the terminal block of the contact input/output communication.
DC30V Contact output signal Max. load current AC/DC 800mA (resistance load) (Pin No. 5-18) Rated load voltage Max. AC48V / Max.
RESET HOLD COM BANK1 BANK2 ) RS-232C AC100 240V COM OUT1 OUT2 OUT3 OUT4 OUT5 S.STOP RD SD SG (+) DC 24V (-) COM COM COM GND 6-2 -A/-COM -B/-COM -B/-COM -A/-COM CEU5 +12V CEU5 3 +12V 1K A 680 COM +12V +12V 680 COM +12 V DC12V,60mA GND F .G . , , 10 - 6-3 (,,) 15mA 10ms COM NPN PNP COM DC24V DC12V PNP ,DC-,NPN ,DC+ CEU5 COM 1 2.2 (DC24V DC12V) 6-4 (,) NPN PNP (OUT15)(S.STOP
Signals name: Position Detected, Origin Calculated, Program End, Error Maximum terminal Voltage: DC +30V Maximum Current: 50mA (050) Output Internals Circuit Connection Method Model Controller: CEU2 NPN Output Transistor Max DC +30V , 50mA OUT Load CEU2 COM Controller: CEU2P PNP Output Transistor OUT Load CEU2P COM Max DC +30V , 50mA 27 7-3-5 Solenoid valves wiring Solenoid valve Driving
DC coil 2. Actuator drive When an actuator, such as a cylinder, is to be driven using a valve, take appropriate measures (such as the installation of a cover or the restricting of access to the product) to prevent potential danger caused by actuator operation. 3.
When the rated voltage is AC and if it is assembled with the coil for DC, response may be delayed and occur malfunction. Also, for DC valves, when the coil for AC is assembled, it occurs malfunction. Pay attention that the coil is assembled correctly after performing maintenance for the coil.
Y terminal: Equivalent to 1.25-3Y of Japan Solderless Terminal 4 pin type 5 pin type Key Key 2(Unused) 2(Unused) 1(Unused) 1(Grounding) 4(Power supply) 3(Power supply) 3(Power supply) 4 (Power supply) 5(Grounding) Series 4 pin type 5 pin type DC AC DC AC SGC Note) SGH Note) 9 SGC200-OMM0002-F SGC / SGH Series Coolant Valve / Precautions 7 Be sure to read this before handling.
Signal name Identification Pin colour Description 2 4 1 DC(+) Red Connect the power supply(+) of the product 2 External switch signal Note) White Blow starts by connecting with DC(-) 3 F.G. Green Frame ground of the product Ground resistance of 100 or less 1 3 4 DC(-) Black Connect the power supply(-) of the product Pin No.
Polarity When connecting power to a solenoid valve with a DC specification and equipped with a light or surge voltage suppressor, check for polarity. If there is polarity, take note of the following. No diode to protect polarity.
DC24V Contact output signal (Alarm) Max. load current AC/DC 500mA (resistance load) Rated load voltage Max. AC48V/ Max.
Warning Caution Surge Voltage Suppressor Caution L and M plug connector
As a valve not mentioned above can also be used depending on the operating conditions (in particular, DC specification valves) , please contact SMC for further information. 2.
Polarity When connecting power to a solenoid valve with a DC specification and equipped with a light or surge voltage suppressor, check for polarity. If there is polarity, take note of the following. No diode to protect polarity.
MRHQ Lead wire length (m) Applicable model Applicable load In-line 0.5 (Nil) 3 (L) 5 (Z) DC AC Load voltage Auto switch model Electrical entry Flexible lead wire(2) (-61) Special function Electrical entry Indicator light Wiring (Output) Perpendicular Pre-wire connector Type 32 40 Misc.
Lead wire length (m) Load voltage Indicator Style Special function Wiring (Output) Electrical entry Auto switch model Applicable load 0.5 () 3 (L) 5 (Z) None (N) DC AC 3 wire (NPN equiv.)
Note 3) To operate a relay as the load on the D-F7BV, J79(C)(W), F9B(V), F7NWV, F79W, F98W(V), F7BWV, F7BA, F7LF, or F9BA, use 24V DC because, the operation could become unstable due to an internal voltage drop if 12V DC is used. Ex.)
MRHQ Lead wire length (m) Applicable model Applicable load In-line 0.5 (Nil) 3 (L) 5 (Z) DC AC Load voltage Auto switch model Electrical entry Flexible lead wire(2) (-61) Special function Electrical entry Indicator light Wiring (Output) Perpendicular Pre-wire connector Type 32 40 Misc.
light Note) VP Power consumption (DC) Option Note) At rated voltage S070 Piping and other usage are the same as standard products.