Miniature Guide Rod Cylinder Allowable eccentric load Caution Make sure that the load mass (W) is within the range in the graph below when there is an eccentric distance (L) from the center of the cylinder. Using cylinders are beyond the limit may shorten the product service life or cause damage. 4-4.
Note5)7) Max. 126 Max. 222 Max. 222 Type Note6) Non-magnetizing lock specification Lock unit Holding force [N] 47 78 157 72 108 216 75 113 245 Power consumption [W] Note7) 5 5 5 Power supply voltage [V] 24VDC10% Note1) Please consult with SMC for non-standard strokes as they are produced as special orders.
. < Size > Width of L: 2.0 to 2.4[mm] Thickness of W: 0.5 to 0.6 [mm] L W Magnified view of the end of the flat blade screwdriver IP address Setup IP address x100 x10 x1 0 0 0 Remote Control mode Note 1) 0 0 1 192.168.1.1 (Factory default value) 0 0 2 192.168.1.2 : : : : 2 5 4 192.168.1.254 2 5 5 DHCP mode Note 2) 2 5 6 Unused : : : 9 9 9 Note 1) The mode to respond to the commands below
The resistor requirements are: 121 1% metal film 1/4 W Terminating resistors should not be installed at the end of a drop line, only at the two ends of trunk line. -13No.EX-OME0003-H Power supply wiring Connect a power supply cable connector to the power supply connector on the SI unit.
. < Size > Width of L: 2.0 to 2.4[mm] Thickness of W: 0.5 to 0.6 [mm] L W Magnified view of the end of the flat blade screwdriver IP address Setup IP address x100 x10 x1 0 0 0 Remote Control mode Note 1) 0 0 1 192.168.1.1 (Factory default value) 0 0 2 192.168.1.2 : : : : 2 5 4 192.168.1.254 2 5 5 DHCP mode Note 2) 2 5 6 Unused : : : 9 9 9 Note 1) The mode to set IP address by DHCP server.
7 Rod Cover assembly MHL-A1007 MHL-A1607 MHL-A2007 MHL-A2507 MHL-A3207 MHL-A4007 Finger assembly Pinion assembly MHL-A1008 MHL-A1009 MHL-A1608 MHL-A1609 MHL-A2008 MHL-A2009 MHL-A2508 MHL-A2509 MHL-A3208 MHL-A3209 MHL-A4008 MHL-A4009 w!8@1@5 tyu@3@4 Order 1 pinion assembly per one unit.
6 Aluminum alloy Anodized Cold-rolled steel Finger Rod seal cover B Electroless nickel plated w !7 Stainless steel Stainless steel Piston rod Washer Nitriding e !8 Sainless steel Rack r Oil containing polyacetal with back metal Bearing !
Length: 5 (5m), Driver Type: 92 (LECSN2-T-9, 200~240V, Absolute, EhterNet/IPâ„¢ Card), I/O Cable Length: H (w/Cable, Connector Only)
Length: 5 (5m), Driver Type: 92 (LECSN2-T-9, 200~240V, Absolute, EhterNet/IPâ„¢ Card), I/O Cable Length: H (w/Cable, Connector Only)
Magnet: D (Built-in Magnet), Mounting: T (Head Trunnion), Type: A (Air Cushion), Bore: 40mm, Port Thread Type: Rc (or M5, Depending on Style, Bore Size, and Thread Combination), Stroke: 1200mm, Thread: Male Rod End, Suffix for Cylinder: w/o Rod Boot, Pivot Bracket: N (Pivot Bracket not Assembled), Rod End Bracket: W (Double Knuckle Joint)
: C6 (Body Ported ø6 One-touch Fitting), Bracket: F2 (w/side Bracket)
Rated Vacuum Range: F (-100 to 100 kPa), Output Specification: T (PNP Open Collector 2 Outputs + Analog Voltage Output), Unit Specification: Unit Selection Function, Switches w/Unit Selection not Permitted for Use in Japan, Piping Specification: C6H (ø6 One-touch Fitting, Straight Type), Lead Wire: J (Lead Wire w/Connector, 5-core, 2 m Lead Wire), Bracket: A1 (Bracket A, Vertical Mounting
Function: 1 (Normally Closed), Piping: 4 (Base Mounted), Body Option: Individual EXH, Specifications: Standard, Voltage: 4 (220VAC 50/60HZ), Lead Wire: D (DIN Connector w/Connector), Surge Suppressor: Z (Light & Surge Suppressor), Manual Override: Non-locking Push Style, Port Size: 01 (Base Mounted w/Sub-plate 1/8), Thread: T (NPTF)
/N.C.), Mounting/Porting: 0 (Base Mounted), Seal: 0 (Rubber), Pilot Specification: Internal Pilot, Back Pressure Check Valve: H (Built-in), Pilot Valve: Standard (0.7MPa), Coil Specification: T (w/Power Saving Circuit, Continuous Duty Type), Voltage: 5 (24VDC), Light/Surge Suppressor/Common Specification: NZ (w/Light Surge Voltage Suppressor, Negative Common), Manual Override: D (Push-turn
/8, Non-plug-in Standard 3/8), Thread: T (NPTF)
), A,B Port Thread: 03 (Base Mounted: Rc 3/8 w/Sub-plate)
), A,B Port Thread: 03 (Base Mounted: Rc 3/8 w/Sub-plate)
Body Size: 42, Pilot Type: 2 (Internal Pilot Solenoid), Port: 03 (3/8), Thread: T (NPTF), Voltage: 6 (12 VDC), Electrical Entry: M (M Plug Connector w/Lead Wire 0.3m), Light/Surge Voltage Suppressor: U (w/Light Surge Voltage Suppressor, Non-polar Type), Manual Override: Non-locking Push Style or None, Option: N (Pilot Exhaust Silencer)