Material: C (Aluminum Cover, SPCD Case, NBR Gasket/O-ring, Nylon Seal), Element Length: B [ℓ500 (ℓ250 x 2)], Port Size: 04 (1/2 Rc), Element Type: B (Sintered Metal, Bronze Material), Nominal Filtration Accuracy: 5 μm, Element Seal Material: N (NBR), Accessory: B (Bracket)
SI unit for EtherNet/IP TM . : Standard wiring of the manifold is for double-solenoid valves and the output number starts at the A side and then B side in that order as shown in the figure a.
SPEEDCON connector wiring method is explained below. (1)Align the mark B on the metal bracket of the cable side connector (plug/socket) with the mark A. Wiring Setting and Adjustment OFF OFF OFF OFF OFF (3)When the mark B of the connector has been turned 180 degrees (1/2 turn), wiring is completed. Confirm that the connection is not loose.
To obtain the operation manual about this product and control unit, please refer to the SMC website (URL http://www.smcworld.com) or contact SMC directly. 2 Display cover Open at the switch configuration. (3)When mark B has been turned 180 degrees (1/2 turn), wiring is complete. Confirm that the connection is not loose.
Verify the specifications before use. 5 Branch port B (COM B) 4 (Input: Max. 32 points/Output: Max. 32 points per branch) Number of branches Connect the SI unit (with manifold valves) or input unit using a branch cable.
L/A OUT L/A IN 2 Display cover Open to access the setting switches. (3)When mark B has been turned 180 degrees (1/2 turn), wiring is complete. Confirm that the connection is not loose. If turned too far, it will become difficult to remove the connector. Displays the communication status of the BUS OUT side physical layer.
An injury can result. 3 Power supply for input and control: 24 VDC 10% Power supply for solenoid valves: 24 VDC +10%/-5% Power supply voltage range 4 Branch port A (COM A) L 5 Branch port B (COM B) Power supply for input and control: 6.2 A (GW unit internal current consumption: 200 mA or less) Power supply for solenoid valves: 4 A Connect the SI unit (with manifold valves) or input unit using
L/A OUT L/A IN Displays the communication status of the BUS OUT side. 2 Display cover The display cover should not be opened. (3)When mark B has been turned 180 degrees (1/2 turn), wiring is complete. Confirm that the connection is not loose. If turned too far, it will become difficult to remove the connector.
SPEEDCON connector wiring method is explained below. (1)Align the mark B on the metal bracket of the cable side connector (plug/socket) with the mark A. Wiring 3 4 1 2 (3)When the mark B of the connector has been turned 180 degrees (1/2 turn), wiring is completed. Confirm that the connection is not loose.
For removal, release the catch with a screwdriver in the direction of the arrow shown in Fig. b. Refer to the SMC website (URL http://www.smcworld.com) for more information about troubleshooting.
A B Press the or button to change the set value. The button is to increase and the button is to decrease the set value. 2 B D D Press the button continuously to keep increasing the set value.
. -28No.LFE*-OMZ0012 Analogue output Flow/Analogue output Output A B C Voltage output 1 V 1.1 V 5 V C Current output 4 mA 4.4 mA 20 mA Rated flow [L/min] Model B Minimum Maximum A LFE1 0.5 20 LFE2 2.5 100 Flow rate 0 Minimum Maximum rated flow LFE3 5 200 rated flow Out of range -29No.LFE*-OMZ0012 Dimensions 2XPort size Note) The electrical entry for lead wire with M12 connector does not rotate
Peak hold: "P" Bottom hold: "b" LCD Charge amount Peak/Bottom hold value IZH10 Thank you for purchasing an SMC IZH10 Series Handheld Electrostatic Meter. Please read this manual carefully before operating the product and make sure you understand its capabilities and limitations. Please keep this manual handy for future reference.
(Or None in the Case of No Switch), Auto Switch Mounting Type: B (Band Mounting), Made to Order Option: XC3 (Special Port Location), Rod Port Location (from Rod Side): B, Head Port Location (from Rod Side): B
Size/Valve Type: 3 (10A, N.C.), Body/Port/Orifice: B (C37; Port 3/8; Orifice 10), Voltage/Electrical Entry: A (24VDC, Grommet), Other Voltages and Electrical Options: None, Other Options: B (NPT Thread), Bracket: XB (w/Bracket), Rotation Angle: B (180°)
Size/Valve Type: 3 (10A, N.C.), Body/Port/Orifice: B (C37; Port 3/8; Orifice 10), Voltage/Electrical Entry: A (24VDC, Grommet), Other Voltages and Electrical Options: None, Other Options: B (NPT Thread), Bracket: XC (w/o Bracket), Rotation Angle: B (180°)
B Sets alarm which is selected for contact output 3. [-] is displayed when the setting of the output signal of contact output3 is not selected alarm signal. ---(AL.01) Contact output signal 3 selected alarm 2.4 Setting and checking HRSH Series 2-4 HRX-OM-R028 Chapter 2 Contact input/output communication 2.4.2 Setting and checking Communication mode Setting and checking 1.
Description Note 1 Rod cover 2A Head cover A For Basic type 2B Head cover B For Boss-cut type 2C Head cover C For Integral clevis type 3 Cylinder tube 4 Piston 5 Piston rod 6 Bushing 7 Seal retainer 8 Retaining ring 9 Bumper A 10 Bumper B 25 or largerThe same as bumper A 11 Rod seal 12 Piston seal 13 Wear ring 14 Bushing for clevis 15 Mounting nut 16 Rod end nut 17 Plastic magnet For CDM2
A B 40 9 9 5 5 50 9.5 8.5 5.5 4.5 63 12.5 11.5 8.5 7.5 80 16.5 13.5 12.5 9.5 100 18 16 14 12 Note)Abjust the auto switch after confirming the operating conditions in the actual setting.
Size: 25, Motor Mounting Position: D (In-line), Motor Type: H (Battery-less Absolute, Step Motor 24 VDC), Lead, mm: B (Size 16: 5; Size 25: 6; Size 32: 8), Stroke: 250mm, Motor Option: B (with Lock), Rod End Thread: Rod End Female Thread, Mounting: Ends Tapped, Body Bottom Tapped, Controller Position: B (Integrated Controller), Parallel Input: 6 (PNP)