LA-OMP0023 Impact at the stroke ends may damage the Card Motor. (6) For pushing operations, set the target position at least 1 mm away from the position where the pushing tool comes into contact with the work piece.
Vacuum Pump Flow Rate Characteristics The graph shows the suction flow rate characteristics of the vacuum pump system at different vacuum pressure. ZK2P00 The actual suction flow at the point of suction varies depending on the piping conditions to the vacuum port. (The above graph shows the value when V port is 8.)
The valves at the inlet and outlet of the piping of the product are not fully opened. Be sure to fully open the valves at the inlet and outlet of the product. The air filter, etc. installed in the compressed air piping has got clogged. Replace the element of the air filter.
Speed at a rated motor rotation of 3000rpm Accel.
Supply Pressure Set the supply pressure at 0.25 to 0.5 MPa. If setting at less than 0.25 MPa, malfunction of the release brake may occur. If line pressure is used directly as supply pressure, any fluctuation in pressure will appear in the form of changes in cylinder characteristics.
Fingers synchronized by a rack and pinion mechanism Model/Stroke Max operating frequency (c.p.m) Opening/closing stroke (L2L1)(mm) Weight (g) Width at closing (mm) (L1) Width at opening (mm) (L2) Bore size (mm) Model Built-in dust proofing mechanism 60 20 40 60 30 60 80 40 80 100 50 100 120 70 120 160 100 160 200 56 78 96 68 110 130 82 142 162 100 182 200 150 198 242 188 246 286 76 118 156
During the operating stroke at initial actuation, the cylinder moves at a slow speed from to due to the fixed throttle of the SSC valve. When it reaches , the head pressure (PH) rises quickly as indicated by the line from to .
CAUTION During the dryer operation, keep the ball valve open at all times. When the ball valve is closed, the condensate drain cannot be discharged. Keep the drain cock at S side. If the drain cock is at O side, compressed air continues to bleed.
Set the supply pressure at 0.25 to 0.5 MPa. If setting at less than 0.25 MPa, malfunction of the release brake may occur. If line pressure is used directly as supply pressure, any fluctuation in pressure will appear in the form of changes in cylinder characteristics.
Set the supply pressure at 0.25 to 0.5 MPa. If setting at less than 0.25 MPa, malfunction of the release brake may occur. If line pressure is used directly as supply pressure, any fluctuation in pressure will appear in the form of changes in cylinder characteristics.
Set the supply pressure at 0.25 to 0.5 MPa. If setting at less than 0.25 MPa, malfunction of the release brake may occur. If line pressure is used directly as supply pressure, any fluctuation in pressure will appear in the form of changes in cylinder characteristics.
Easy control at low speeds Effective area of controlled flow is about one tenth of the standard series. Suitable for control of low speed cylinders at 10 to 50mm/sec. Operating strokes at low speed and return strokes at high speed Effective area of free flow units are the same as standard.
accessory E: 110 At accessory F: 110 { } 5 150 Approx.194 125 G1/2 Electric conduit 35 At accessory E: 195 At accessory F: 275 { } 4 x M8 x 1.25 depth12 (Female thread for rear mounting) With optional resin cable clamp Applicable cable O.
Displacement at "A" when a load is applied to "F" with the slide table retracted. Displacement at the section indicated by the arrow when a load is applied to this section with the slide table fully extended.
accessory E: 110 At accessory F: 110 { } 5 150 194 125 G1/2 Electric conduit 35 At accessory E: 195 At accessory F: 275 { } 4 x M8 x 1.25 depth12 (Female thread for rear mounting) With optional resin cable clamp Applicable cable O.
The entry at Sub-Index 0 describes the number of errors that have been stored. Every new error is stored at Sub-Index 1, the older ones move down the list. If 0 is written at the Sub-Index 0, error history is deleted. Values higher than 0 are prevented from being written. Index 1005h COB-ID SYNC message This object defines the COB-ID of the Synchronization Object (SYNC).
Consult SMC concerning water resistance, flexibility of lead wires, and usage at welding sites, etc. 98
(page at left) Suffix -XB10 to the end of standard model no. (page at left) Rubber bumper is standard equipment for long stroke type. Part no. Mounting Bracket Part No. Intermediate strokes by the 1 mm interval are available by using spacers with standard stroke cylinders.
Therefore, when used at near the upper limit, the following guide will be helpful.