High Precision Digital Pressure Switch, Series ZSE50F/ZSE60F, ISE50/ISE60 Reference page Item 3 Output type Example of internal circuit and wiring 4 Auto shift function, Chattering prevention function 5 Measures to be taken when error occurs 6 11 For General Fluids High Precision Digital Pressure Switch Series ZSE60F/ISE60 Dimensions Bracket A A 30 20 20 45 55 4.5 11.5 40 15 4.5 6.5 1.6 20 41.5 Bracket A ZS-24-A View A Bracket D A 30 20 20 45 55 4.5 4.2 11.5 40
Note 2) Drain piping, or piping for a stop valve, like a ball valve, is required. 850 size comes with a ball valve. substitute with (Symbol: A).
Indicator light LED A X A X Can be used for 110V and 115VAC, 220V and 230VAC in common.
6 q w e r t y u i Block packing !
This can be prevented by inserting a noise filter, such as a line noise filter and ferrite core, between the switchmode power supply and the product, or by using a series power supply instead of a switch-mode power supply.
In principle, this function counts each time there is a rise or fall in either of the A or B phase pulses. 2 1 Amplification/ Interpolation circuit Counter A phase B phase Magnetic resistance element Piston rod Magnet Count 1 2 3 4 5 6 7 8 9 10 .
Do not apply a lateral load to the external slider. When a load is mounted directly to the cylinder, variations in the alignment of each shaft center cannot be offset, which results in the generation of a lateral load that can cause malfunction.
In locations which receive direct sunlight, provide a protective cover, etc. 5. In locations near heat sources, protect against radiated heat. 6. In locations where there is contact with spatter from water, oil or solder, etc., implement suitable protective measures. 7.
Use a spanner corresponding to the size of hexagonal portion, or hexagonal portion may become deformed. 3. Tightening the threaded portion of an M3, M5 or M6 fittings 1) M3 First, tighten it by hand, then give it an additional 1/4 turn with a wrench. 2) M5 and M6 First, tighten it by hand, then give it an additional 1/6 turn with a wrench. Mounting Caution 1.
.-.P 6 Single Rod End/Dimensaons . .P 7 Double Rod End/Dimensions.-...P 8
Series:NCRAI How To Order Adluatable cuahlon C Both end cushion Not available on NCRA1BW30 Fotation
Caution Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Warning Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Danger Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury. Warning 1.
A protective cover should be used to shield valves from direct sunlight. 5. Shield valves from radiated heat generated by nearby heat sources. 6. Employ suitable protective measures in locations where there is contact with water droplets, oil, or welding spatter. 7. Install a silencer into port (3) to prevent the ingress of dust if there is a lot of dust in the atmosphere.
Atmospheric vent port Used to mount the product on a DIN rail. DIN rail mount CAUTION indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury.
Lube unit S1 Thread type ALDU600 (with panel) 1a (without oil OFF) S2 Nil Rc NPT Body size (Standard) N 6 9 1B 2B Accessory Port size Float Switch Specifications Symbol Description Nil Bracket Panel 06 10 12 14 20 4 3 Voltage Max. contact capacity Max. operating current Contact point construction Level indication 200 VAC, 200 VDC 50 VA AC, 50 W DC 0.5 A AC, 0.5 A DC 1a, 1b Bottom limit indication
With meter-out control, the exhaust pressure will increase and create a greater sliding resistance. 1.4-81 Low Friction: Double Acting Single Rod Series CM2Q Construction CJ1 CJP CJ2 Component Parts CM2 Description Material Stainless steel No. q No. !1 !2 !3 !4 !5 !6 !7 !
.-.P 6 Single Rod End/Dimensaons . .P 7 Double Rod End/Dimensions.-...P 8
Series:NCRAI How To Order Adluatable cuahlon C Both end cushion Not available on NCRA1BW30 Fotation
(Appropriate tightening torque (Rc1/8 G1/8): 7 to 9 Nm) For 6 one-touch fitting, use tube with O.D. 6 mm, and I.D. 4 mm. For 4 one-touch fitting, use tube with O.D. 4 mm, and I.D. 2.5 mm. Warning How to reset the product after a power cut or forcible de-energizing The setting of the product will be retained as it was before a power cut or de-energizing.
(I) (2) Prepare tools: Prepare a hexagon wrench key. The hexagon wrench key VBA1 for VBA1 is with nominal size 4 and 6, for VBA2 with VBA2 nominal size 8, and for the drain port with nominal size 6. OUT port Safety valve port (J) Rc3/8 : Tighten the optional safety valve and drain valve with a monkey spanner.
C.O. 1/8 to 2 10 to 50 3/8 to 1 32 A to 80 A 7.1 to 15.8 Series VND Series VNB Bronze Stainless steel PTFE N.C.
SGC200*-OMJ0004-A SGC/SGH / / / / / / / / -2,3 -4 -4 -5 -5 -5 -5,6 -6 -710 -11,12 -1SGC200*-OMJ0004-A (ISO/IEC)(JIS) 1) 2) *1) ISO 4414: Pneumatic fluid power -General rules relating to systems. ISO 4413: Hydraulic fluid power -General rules relating to systems. IEC 60204-1: Safety of machinery -Electrical equipment of machines.