180 Angular Style Air Gripper Series MHY2/MHW2 Cam Style Rack & Pinion Style 1 Example) For setting the gripping force to be at least 20 times the work weight; Required gripping force = 0.05 kg x 20 x 9.8 m/s2 = 10 N min.
(Refer to Precautions on page 16-2-24 for details.) 1.5 01: R 1/8 T1: NPT 1/8 Data ZSE40(F)/ISE40-W1 2-M4 x 0.7 thread depth 4 20 30 Rc 1/8 MPa 7 19 20 30 OUT2 OUT1 SET 6.5 R 6.4 18.35 Atmospheric release port Lead wire length 600 (3000) 3.5 12.4 7.8 7 2.5 2.6 30 15.2 42 10.7 4 6 For splash proof use (IP65), insert an air tube into the atmospheric release port.
External Pilot Mounting Direction of Pilot Solenoid Valve Caution Caution VC When replacing a valve, if an external pilot solenoid valve is mounted in the wrong direction, it may malfunction or leak air. Pilot port P1 and P2 piping Please arrange P1 and P2 piping as follows according to the model.
When ordering nuts as spare parts, size 4 and 5 are as shown below.
series 02 03 04 06 10 12 14 20 Caution L (2) Note 1) AS800 is available as special.
Example) Assume circuit C with an operating pressure of 0.5 MPa, load weight of 10 kg, fluctuation to 20 kg and a cylinder bore of 32 mm.
oil odor. 3) Use the length of time calculated in step 2) as an approximate effective deodorization time.
Avoid excessive torsional moment or bending moment other than those caused by the equipments own weight as this can cause damage. Support external piping separately. 3. Piping materials without flexibility such as steel tube piping are prone to be affected by excess moment load and vibration from the piping side. Use flexible tubing in between to avoid such an effect. 1100
Avoid excessive torsional moment or bending moment other than those caused by the equipments own weight as this can cause damage. Support external piping separately. 3. Piping materials without flexibility such as steel tube piping are prone to be affected by excess moment load and vibration from the piping side. Use flexible tubing in between to avoid such an effect. 1100
BIT 4 Stp-No.bit3 (7) 20 Step designation BIT 5 Stp-No.bit4 (20) 8 BIT 6 Stp-No.bit5 (8) 21 BIT 7 Stp-No.bit6 (21) 9 Stp-No.bit7 (9) 22 SET-ON 10 Temporarily stops the program run by means of the ON input. (3) Temporary stop HOLD READY 23 BUSY < 2 > 11 (16) Emergency stop (nonlogical input) Performs an emergency stop when ON input stops.
Please take all available precautions, as the life of the equipment is affected by conditions of usage. 4. The piston chamber and bellows chamber are directly connected to the atmosphere. Use in an environment where particulate discharge will not present a problem. High temperature type 1.
a place that will be used as a scaffold during piping.
Also suited for use in areas in which water splashes, such as food processing equipment or car washers. Bore size (mm) 20 E1 E2 NN1 M22 X 1.5 NN2 M20 X 1.5 22 0 0.033 20 0 0.033 These dimensions and other dimensions are the same as standard style.
It depends on the actuator type and the lead. 2) Direct Teaching cannot be performed on an actuator with lock as the lock is held even when the servo is turned OFF.
Material 20 25 32 40 Piston seal NLP-20A NLP-19A NLP-32A NLP-40A NBR !
(b) [F 1] Setting of OUT1 The default setting is as follows. If no problem is caused by this setting, keep these settings. Item Default setting The following instructions must be followed during maintenance: Turn off the power supply Stop the air supply, exhaust the residual pressure and verify that the air is released before performing maintenance work Otherwise an injury can result.
This product cannot be used as a check regulator by installing it between solenoid valve and actuator. 3. Port with a pressure gauge or a plug can be used as an OUT port.
Furthermore, it cannot be used as an emergency cutoff valve. Terminal deceleration and an intermediate speed change circuit can be produced easily. Universal porting could be used as a selector/divider valve. The simple system configuration permits sharp response. The large capacity system configuration without connection loss allows the use of smaller valves and piping.
The Booster Lube cannot be used in an environment or in a location that is exposed to synthetic oil, thinner, acetone, alcohol, organic solvets such as ethylene chloride, chemicals such as sulfuric acid or nitric acid, cutting oil, kerosene, gasoline, or a threadlock agent, etc., because they will be damaged. F.R.L.