AS-FPQ/AS-FPG (mm) Applicable cylinder bore size (mm) 4 6 8 10 12 AS-FPG AS-FPQ Clean performance Resin: PP Metal: Brass (electroless nickel plated) Resin: PP Metal: Stainless steel (SUS304) M5 x 0.8 6, 10, 16, 20 AS121FP-M5 R 1/8 20, 25, 32 AS221FP-01 R 1/4 20, 25, 32, 40 AS221FP-02 R 3/8 40, 50, 63 AS321FP-03 10-AS-F 10-AS-FG R 1/2 63, 80, 100 AS421FP-04 Resin: PBT, POM Metal: Brass (electroless nickel
0.3 0.4 0.5 0.6 Suction flow (l/min(ANR)) Supply pressure (MPa) ZQ110 Exhaust characteristics ZQ110 Flow characteristics Maximum suction flow (l/min(ANR)) Air consumption (l/min(ANR)) Maximum vacuum pressure (kPa) Maximum vacuum pressure (kPa) Maximum vacuum pressure -80 -80 60 -60 -60 50 40 -40 -40 30 Air consumption 20 -20 -20 10 Maximum suction flow Suction flow (l/min(ANR)) 25 20 15
Maximum suction flow (l/min(ANR)) Air consumption (l/min(ANR)) Maximum vacuum pressure (kPa) Maximum vacuum pressure (kPa) Maximum vacuum pressure -80 -80 60 -60 -60 50 40 -40 -40 30 Air consumption 20 -20 -20 10 Maximum suction flow Suction flow (l/min(ANR)) 25 20 15 10 5 0 0.1 0 0.2 0.3 0.4 0.5 0.6 Supply pressure (MPa) 13-9-3 4 Series ZQ Specifications Ejector Weight Switch and suction
Nil Without auto switch (Built-in magnet) S 1 pc. 6 25 6 mm 25 mm For the applicable auto switch model, refer to the table below. n n pcs. 10 32 10 mm 32 mm 15 40 15 mm 40 mm Adjustment type 20 20 mm Nil With adjusting bolt B With shock absorbers (2 pcs.) Port thread type With shock absorber (With plate A) Installed on side A at time of shipment.
Before using the precision regulator, be sure to install the pressure gauge at the gauge port of the precision regulator. At this time, the recommended tightening torque of the pressure gauge is 7 to 9 Nm. 822 IR1000/2000/3000 Series Specific Product Precautions 2 Be sure to read this before handling the products.
If the installation is using accurate control, wait until the product has warmed up (approximately 20 to 30 minutes). OUT1 OUT2 n_2 n_4 n_1 n_3 4, Selection of auto-preset OUT2 Press the button to display [AP2]. Automatic identification function release (When at least 1 sensor other than PSE530 series will be connected.)
At least 3.5 characters of silent interval are necessary at the beginning and the end of the communication frame. b) Device Address This is a number to identify this product. 1" is the default setting.
To connect the IN side, hold the valve guide at its wrench flats (opposite side 10) and tighten it at the recommended torque of 1.5 to 2 Nm. Excessive torque or holding it at an area other than the specified portion may result in a malfunction. 2.
SOLENOID SPECIFICATIONS Adder Number 0 1 Required Amplifier VEA1 30, VEA131 vEA 250, 251 ,252 Control Range 0-750mA 0 1 A Coil Resistance 26]2 (68"F (20"C) ) 1312 (68"F (20'C)) PorYer Consumotion 15W Max. Current (68"F (20"C) ) 13W Max. Current (68"F (20'C)) Insulation Class H Max. TempeEture Rise 284'F (140"C) at Full Current Elec-trical Connection DIN Connector (h" PF) NVEF.
HOLD: Fix the output at the current value. Software control: Clear, Hold or Set for individual points can be set by software bit.
(or 3 kPa) Repeatability Note 2) 0.4 MPa setting (Ex.)10-ARP30-02BG 1 L/min [ANR] or less (at P2 = 0.4 MPa) 0.2 MPa setting (Ex.)10-ARP30-02BG-1 0.6 L/min [ANR] or less (at P2 = 0.2 MPa) Air consumption 0.6 MPa setting (Ex.)10-ARP30-02BG-3 1.4 L/min [ANR] or less (at P2 = 0.6 MPa) 1/8 1/4 1/8 Pressure gauge port size 5 to 60C (No freezing) Ambient and fluid temperature With a digital pressure
(or 3 kPa) Repeatability Note 2) 0.4 MPa setting (Ex.)10-ARP30-02BG 1 L/min [ANR] or less (at P2 = 0.4 MPa) 0.2 MPa setting (Ex.)10-ARP30-02BG-1 0.6 L/min [ANR] or less (at P2 = 0.2 MPa) Air consumption 0.6 MPa setting (Ex.)10-ARP30-02BG-3 1.4 L/min [ANR] or less (at P2 = 0.6 MPa) 1/8 1/4 1/8 Pressure gauge port size 5 to 60C (No freezing) Ambient and fluid temperature With a digital pressure
The Cv factor for valves with back pressure check valve will be about 20% less than in the table above. Vibration resistance: No malfunction when tested with one sweep of 8.3 to 2000Hz in the axial direction and at a right angle to the main valve and armature, one time each in both energized and deenergized states.
When a pushing operation is performed at the maximum allowable set thrust at 100% duty ratio or more, stop (end) the operation within 10 seconds.
Problem Possible causes Investigation and countermeasures 1: Adjust the NFC reader/writer so that it is positioned at the centre of the NFC antenna (circled part). 1.
Problem Possible causes Investigation and countermeasures 1: Adjust the NFC reader/writer so that it is positioned at the centre of the NFC antenna (circled part). 1.
Problem Possible causes Investigation and countermeasures 1: Adjust the NFC reader/writer so that it is positioned at the centre of the NFC antenna (circled part). 1.
Pressure control 1) Rotate the adjustment wheel counterclockwise completely to relieve spring force. 2) Partially open the valve at inlet side to supply gas to the back pressure regulator. 3) Increase the inlet pressure to the setting pressure by rotating the adjustment wheel clockwise. 4) Continue opening the valve at inlet side monitoring the inlet pressure.
Test was performed at both energized and de-energized states in the axial direction and at the right angles to the main valve and armature. (Values at the initial period) Caution Vibration resistance: For Safety Instructions and Solenoid Valve Precautions, refer to page 3-13-2.
NVF353O f l Operating prs6sur range 2 pGiEon singb 20 -129 PSI S(1.5 -gkgF) 2 pssition double-15-128 P$l (1 -gkgflcm'?) Arntient and tluid temperatureMax .120'F(Max. 50'C) Respon time 2 poitl'| slngle/doubb 20ms or less at 75 PSI (skg/cm'?) 3 pcition 40ms or less at 75 PSI (skgf/cm'?)