Clean One-touch Fittings For Driving Air Piping KPQ/KPG Series Removal of tubing 1) The outside diameter of tubes that have been used at high temperatures or for long periods of time will expand, and in some cases pipe fittings cannot be reattached. Tubes that cannot be attached should be discarded and replaced with new ones.
(Coil temperature: 20C, pressure: 0.5 MPa, at rated voltage, with light and surge suppressor, value at operation excluding restart period) The period immediately after a restart may be delayed for about 1 msec depending on operating conditions. Note 2) Use dry air to prevent condensation when operating at low temperatures.
At inlel pressure 0.7MPa 1 7.1 kgflcm2! AI Inlel pressure 0.7MPa /71 kgf/cm21 , outlel pressure 0.2MPa 1 2.0kgflcm21. flow rale 20 / min (ANR) AR2001-02 AR2001-02 0.25 -r-=:: lf~1 ~ "'" ~ :'.. ::;; 0.2 ~r. " 5 OJ> ~ o . 3k-1-j.-:=.
(Value at the initial state) Impact resistance Conditions when tested with a drop tester in the axial direction and at a right angle to the armature, one time each in energized and deenergized states. No malfunction occurred when tested.
In order to correct the deviation, the controller increases the output signal until the pressure on the pressure sensor converges at 250 kPa. Step 1 Step 2 Step 3 Step 4 . . . . . . . . . . . . . Step 20 Step 5 P4 Set pressure P3
S. t o t he el ect ropneum at i c regul at or t hrough t he m ast er PLC ( e. g. ent eri ng a t arget val ue t o t he out put w ord dat a area) . Set D at e 0h 0FFFh [ ( aF. S. ) 4095] H EX O ut put pressure 0% F. S. 100% F.
Current leakage 100 A or less at 24 VDC Indicator LED Red LED illuminates when turned ON.
(mm) Applicable cylinder bore size (mm) 4 6 8 10 12 AS-FPG AS-FPQ Clean performance Resin: PP Metal: Brass (electroless nickel plated) Resin: PP Metal: Stainless steel 304 M5 x 0.8 6, 10, 16, 20 AS121FP-M5 R 1/8 20, 25, 32 AS221FP-01 R 1/4 20, 25, 32, 40 AS221FP-02 R 3/8 40, 50, 63 AS321FP-03 10-AS-F 10-AS-FG R 1/2 63, 80, 100 AS421FP-04 Resin: PBT, POM Metal: Brass (electroless nickel plated
(mm) Applicable cylinder bore size (mm) 4 6 8 10 12 AS-FPG AS-FPQ Clean performance Resin: PP Metal: Brass (electroless nickel plated) Resin: PP Metal: Stainless steel (SUS304) M5 x 0.8 6, 10, 16, 20 AS121FP-M5 R 1/8 20, 25, 32 AS221FP-01 R 1/4 20, 25, 32, 40 AS221FP-02 R 3/8 40, 50, 63 AS321FP-03 10-AS-F 10-AS-FG R 1/2 63, 80, 100 AS421FP-04 Resin: PBT, POM Metal: Brass (electroless nickel
0.3 0.4 0.5 0.6 Suction flow (l/min(ANR)) Supply pressure (MPa) ZQ110 Exhaust characteristics ZQ110 Flow characteristics Maximum suction flow (l/min(ANR)) Air consumption (l/min(ANR)) Maximum vacuum pressure (kPa) Maximum vacuum pressure (kPa) Maximum vacuum pressure -80 -80 60 -60 -60 50 40 -40 -40 30 Air consumption 20 -20 -20 10 Maximum suction flow Suction flow (l/min(ANR)) 25 20 15
Maximum suction flow (l/min(ANR)) Air consumption (l/min(ANR)) Maximum vacuum pressure (kPa) Maximum vacuum pressure (kPa) Maximum vacuum pressure -80 -80 60 -60 -60 50 40 -40 -40 30 Air consumption 20 -20 -20 10 Maximum suction flow Suction flow (l/min(ANR)) 25 20 15 10 5 0 0.1 0 0.2 0.3 0.4 0.5 0.6 Supply pressure (MPa) 13-9-3 4 Series ZQ Specifications Ejector Weight Switch and suction
Nil Without auto switch (Built-in magnet) S 1 pc. 6 25 6 mm 25 mm For the applicable auto switch model, refer to the table below. n n pcs. 10 32 10 mm 32 mm 15 40 15 mm 40 mm Adjustment type 20 20 mm Nil With adjusting bolt B With shock absorbers (2 pcs.) Port thread type With shock absorber (With plate A) Installed on side A at time of shipment.
Before using the precision regulator, be sure to install the pressure gauge at the gauge port of the precision regulator. At this time, the recommended tightening torque of the pressure gauge is 7 to 9 Nm. 822 IR1000/2000/3000 Series Specific Product Precautions 2 Be sure to read this before handling the products.
If the installation is using accurate control, wait until the product has warmed up (approximately 20 to 30 minutes). OUT1 OUT2 n_2 n_4 n_1 n_3 4, Selection of auto-preset OUT2 Press the button to display [AP2]. Automatic identification function release (When at least 1 sensor other than PSE530 series will be connected.)
At least 3.5 characters of silent interval are necessary at the beginning and the end of the communication frame. b) Device Address This is a number to identify this product. 1" is the default setting.
To connect the IN side, hold the valve guide at its wrench flats (opposite side 10) and tighten it at the recommended torque of 1.5 to 2 Nm. Excessive torque or holding it at an area other than the specified portion may result in a malfunction. 2.
SOLENOID SPECIFICATIONS Adder Number 0 1 Required Amplifier VEA1 30, VEA131 vEA 250, 251 ,252 Control Range 0-750mA 0 1 A Coil Resistance 26]2 (68"F (20"C) ) 1312 (68"F (20'C)) PorYer Consumotion 15W Max. Current (68"F (20"C) ) 13W Max. Current (68"F (20'C)) Insulation Class H Max. TempeEture Rise 284'F (140"C) at Full Current Elec-trical Connection DIN Connector (h" PF) NVEF.
HOLD: Fix the output at the current value. Software control: Clear, Hold or Set for individual points can be set by software bit.
(or 3 kPa) Repeatability Note 2) 0.4 MPa setting (Ex.)10-ARP30-02BG 1 L/min [ANR] or less (at P2 = 0.4 MPa) 0.2 MPa setting (Ex.)10-ARP30-02BG-1 0.6 L/min [ANR] or less (at P2 = 0.2 MPa) Air consumption 0.6 MPa setting (Ex.)10-ARP30-02BG-3 1.4 L/min [ANR] or less (at P2 = 0.6 MPa) 1/8 1/4 1/8 Pressure gauge port size 5 to 60C (No freezing) Ambient and fluid temperature With a digital pressure