Ionizer Tungsten Silicon Stainless steel Low-maintenance type /Tungsten Low-maintenance type /Silicon Nil C S F Feedback sensor Autobalance sensor [High-precision type] G J Power supply cable Nil Z N With power supply cable (3 m) With power supply cable (10 m) Without power supply cable K Output specification NPN output PNP output Nil P Control unit cable entry direction Nil R Left-hand entry Right-hand
to 1000 mm/s (Refer to page 10-5-7.) (3) Piston speed H (High speed/High frequency type) 5 mm/s to 3000 mm/s (Refer to page 10-5-7.)
to 1000 mm/s (Refer to page 10-5-7.) (3) Piston speed H (High speed/High frequency type) 5 mm/s to 3000 mm/s (Refer to page 10-5-7.)
Through-hole: CQ2YB/CDQ2YB Both ends tapped style: CQ2YA/CDQ2YA CDQ2YA RE A B Both Ends Tapped (mm) Bore size (mm) O1 R O1 thread REC R R 32 M6 x 1.0 10 40 M6 x 1.0 10 CX 50 M8 x 1.25 14 CY MQQ M RHC H thread effective depth C U 4-N through 8-O counterbore Q F 2-P (Port size) (Rc, NPT, G) MK(2) I RS Q G RS H A 22 D M E Z 11 Lead wire min. bending radius 10 RZQ Auto switch D-A7, A8 MI W S
x 1.5 M26 x 1.5 27 30 31 37 40 1/4 3/8 3/8 1/2 1/2 84 90 98 116 126 146 159 170 204 215 RZQ MI W S CEP1 CE1 CE2 ML2B C J G5-S CV MVGQ CC RB J D-X 20Data 10-4-17
When the SONY Corporation RC-S380/S NFC reader is used. No driver: NFC reader/writer driver is not installed. Refer to Preparation before use (2. Preparation before use (page 7)). R/W undetected: NFC reader/writer driver is installed. NFC reader/ writer is not identified or USB is not connected.
When the SONY Corporation RC-S380/S NFC reader is used. No driver: NFC reader/writer driver is not installed. Refer to Preparation before use (2. Preparation before use (page 7)). R/W undetected: NFC reader/writer driver is installed. NFC reader/ writer is not identified or USB is not connected.
ends a w t o u i Resin materials eliminated Laser marking is employed for the model designation. d t o o g e a n L c 2 s u s d Particulate generation has been reduced at the stroke ends by reducing impact using a sine cushion and by stopping the stroke using an internal stopper. i e Reduction of outgassing due to surface treatment n Impact acceleration [m/s2] o u d t R g g e a c 1 s u s
SETUP I PORTOPORTLOOP SEC mm2/s LABEL PRO Main modes ALM mm/s L C Directs a program operation. RUN Operation mode ACTUATOR & CONSTRUCTION SYSTEM CONTROLLER POWER ALARM STOP Executes a JOG operation.
downward and opens main valve while R port closes simultaneously.
Number of auto switches Nil S n 2 pcs. 1 pc. n pcs.
6 Single acting, spring return Piston seal CQ2B12-S-PS Rod seal NBR 12 16 20 25 32 40 50 CQ2B12-S-PS CQ2B16-S-PS CQ2B20-S-PS CQ2B25-S-PS CQ2B32-S-PS CQ2B40-S-PS CQ2B50-S-PS CQ2B16-S-PS Gasket CQ2B20-S-PS CQ2B25-S-PS CQ2B32-S-PS CQ2B40-S-PS CQ2B50-S-PS Left no. !4. Seal kit includes !4. Order the seal kit, based on each bore size.
Maximum piston speed: 1000 mm/s It can be used at 50 to 1000 mm/s provided that it is within the allowable kinetic energy range.
Maximum piston speed: 1000 mm/s It can be used at 50 to 1000 mm/s provided that it is within the allowable kinetic energy range. CL1 MLGC Taper ring Steel ball CNG P MNB f CNA R R CNS CLS CLQ MLGP RLQ MLU ML1C Manual override for unlocking Even if the air supply is blocked or exhausted, lock release is possible. The fail safe mechanism locks again when the manual override is released.
50 100 200 300 500 700 Average speed Va mm/s Collision speed V mm/s Note) Use average speed to calculate static moment.
Grease pack part number: GR-S-010 (10 g) M3, M5, Rc port, NPT port Use the correct tightening torques listed below.
size (S) PB Port size G1/2 Compatible heavy-duty cord Cable O.D. 6 to 12 L L K 2-M Thread depth 6 K 2-M Thread depth 6 (mm) Electrical entry P Port size B Model A C D E F K L M Grommet: G Conduit: C DIN terminal: D Conduit terminal: T S 68 71 74 74 U 81 91.5 101 103.5 S 51 54 57 57 Q 98 101 104 104 R 36 44 53 55.5 R 40 48 56 58.5 Q 46 50 52 52 R 36 44 53 55.5 Q 63 66 69 69 R 35 42 51 53.5
+0.1 A NA B 0 0.3 S + Stroke H U CZ 0 0.3 Z + Stroke R ZZ + Stroke (mm) * A clevis pin and retaining rings are included.
VK VZ NL: Neon light R: Resister LED: Emitting diode R: Resister D: Protective diode LED: Emitting diode R: Resister VF DIN terminal Light/Surge Voltage Suppressor VFR Caution VP4 Grommet type (G) Rated voltage DIN terminal (D) Part no. symbol W/o indicator light With indicator light W/o indicator light With indicator light W/o indicator light With indicator light VZS Caution S VFS Markings
7 @6 r u #1 t @4 @5 #2 @0 y i !9 !0 q !1 w !