NCA1 Contact SMC if lubrication will be applied. 22 No.JXC-OMW1019-A 9.6 Precautions for electric actuator with lock Warning (1) Do not use the lock as a safety lock or a control that requires a locking force. The lock used for the product with a lock is designed to prevent dropping of work piece. (2) For vertical mounting, use the product with a lock.
C a u t i o n Use a specific mounting bracket (Table 2) and mount the product so that the band of the bracket will be perpendicular to the stroke of the product. Tighten mounting screws to the appropriate torque. The auto switch can only be used for cylinders with a built-in magnet for auto switch (e.g. CDM2).
10.5 [5m ] L E C P *B* (a) (b) 2 A B-1 L 1 A A-1 (b) 6 A B-1 B B-2 1 1.5m 5 A A-1 B A-2 3 3 3m B B-2 COM-A/COM B-3 4 B A-2 COM-B/A-3 5 5m (c) COM-A/COM B-3 Shield COM-B/ A-3 Vcc B-4 12 GND A-4 13 Vcc B-4 A B-5 7 GND A-4 A A-5 6 A B-5 B B-6 9 A A-5 S B A-6 8 (d) B B-6 3 B A-6 (a) + B-1 4 A-1 5 + B-3 1 2 A-3 (a) (8) (14.2) B1 A1 (b) 2 1 (17.7) (14) (18) (10.2) 6
[Check valve] A check valve is a safety device intended to prevent reverse flow. The AP 64 is a unique design with only one moving part in the gas stream, an O-ring. It is a springless design, free of springs and poppets. [Vacuum generator] A venturi device that creates vacuum by flowing gas through a nozzle.
Avoid using in a place that exceeds an ambient temperature range. b. Avoid using in a place that exceeds an ambient humidity range. c. Avoid using in a place where condensation occurs due to a drastic temperature change. d. Avoid using in a place in the presence of corrosive or explosive gas or where there is a volatile combustible. e.
Therefore, internal parts of a cylinder other than rod seal are not replaceable. 2. Use caution to the popping of a retaining ring. When replacing rod seals and removing and mounting a retaining ring, use a proper tool (Retaining ring plier: Tool for installing a type C retaining ring).
It results in generation of a play, increase sliding resistance or air leakage. Consult P/A for in case of usage in such an environment. 3.Install a shade screen if exposed to the direct sun light. 4.Install a blocking cover if a heat source is in the area.
Rotate the pin 30 to the right with a wooden implement such as the grip of a wooden hammer or a resin stick without scratching.
Do not connect the earth to a water pipe, a gas pipe, or a lightening rod. Do not plug too many leads into a single socket. That causes exothermic heat or fire. Do not modify the internal electrical wiring of the product. 10.2 Specifications An earth leakage breaker is installed in the product.
A unit connected to a PLC to communicate input and output data. T Topology Connection configuration of the network -10No.EX-OMX1001 Installation and Wiring Installation Connect valve manifold to the SI unit.
[cm] -70No.PF-OMS0001CN-A PFMC7501/7102/7202 2x A B D E F H K L N PFMC7501/7102 Rc1/2NPT1/2 70 30 60.6 41.2 15 14 26 18 13.6 PFMC7202 Rc3/4NPT3/4G3/4 90 35 66.1 46.7 17.5 24 31 28 16.8 PFMC7501/7102 G1/2 76 30 60.6 41.2 15 14 26 18 13.6 S T U V W PFMC7501/7102 24 22 32 40 50 PFMC7202 30 30 42 48 58 -71No.PF-OMS0001CN-A M8 (ZS-40-A) -72No.PF-OMS0001CN-A Revision history A [September 2016]
[Check valve] A check valve is a safety device intended to prevent reverse flow. The AP 64 is a unique design with only one moving part in the gas stream, an O-ring. It is a springless design, free of springs and poppets. [Vacuum generator] A venturi device that creates vacuum by flowing gas through a nozzle.
3000 a=1000 400 400 L3 mm L3 mm L3 mm a=2000 a=2000 a=2000 400 a=3000 a=3000 a=1000 a 200 200 200 L1 M1 0 2 4 6 8 10 0 5 10 20 15 0 5 10 15 Work load (W) kg Work load (W) kg Work load (W) kg Mounting position Model LJ1S10 LJ1S20 LJ1S30 Direction of load movement 30 150 300 a=500 a=500 a=500 a a=1000 a=2000 a=1000 20 100 200 a=2000 a=2000 a=3000 L1 mm L1 mm L1 mm M1 W 10 50 100 L1 10 30 20
A Parts list Section A enlarged view Description Material Note No.
When a cylinder is used in a clamping mechanism, there is a danger of work pieces dropping if there is a decrease in clamping force due to a drop in circuit pressure caused by a power outage, etc. Therefore, safety equipment should be installed to prevent damage to machinery and human injury.
Devise a safe system so that if a person engages the emergency stop or if a safety device is tripped during a system malfunction,such as a power outage, the operation of the magnet gripper will not cause a hazard to humans or damage the equipment. 7. Consider the action when operation is restarted after an emergency or abnormal stop.
Devise a safe system so that if a person engages the emergency stop or if a safety device is tripped during a system malfunction,such as a power outage, the operation of the magnet gripper will not cause a hazard to humans or damage the equipment. 7. Consider the action when operation is restarted after an emergency or abnormal stop.
range. 03Data field of a command is not normal.