Bore Size: 40mm, Cylinder Port: G, Arm Opening Angle: 120°, Switch Type: P (P & F)

Bore Size: 40mm, Cylinder Port: G, Arm Opening Angle: 135°, Switch Type: P (P & F)

Bore Size: 80mm, Cylinder Port: G, Arm Opening Angle: 120°, Switch Type: P (P & F)

Bore Size: 80mm, Cylinder Port: G, Arm Opening Angle: 30°, Switch Type: P (P & F)

Bore Size: 80mm, Cylinder Port: G, Arm Opening Angle: 45°, Switch Type: P (P & F)

Bore Size: 80mm, Cylinder Port: G, Arm Opening Angle: 135°, Switch Type: P (P & F)

Bore Size: 80mm, Cylinder Port: G, Arm Opening Angle: 60°, Switch Type: P (P & F)

Bore Size: 80mm, Cylinder Port: TN (NPT), Arm Opening Angle: 90°, Switch Type: P (P & F)

Bore Size: 57L (57mm), Port Thread: TF (G), Stroke: 50 (50mm), Switch: P (P&F)

Bore Size: 71 (71mm), Port Thread: TF (G), Stroke: 25 (25mm), Switch: P (P&F)

Bore Size: 57L (57mm), Port Thread: TF (G), Stroke: 25 (25mm), Switch: P (P&F)

Bore Size: 71 (71mm), Port Thread: TF (G), Stroke: 50 (50mm), Switch: P (P&F), Output Display: R (Retracted: Red; Extended: Yellow)

Bore Size: 57L (57mm), Port Thread: TN (NPT), Stroke: 25 (25mm), Switch: P (P&F)

Bore Size: 71 (71mm), Port Thread: TN (NPT), Stroke: 25 (25mm), Switch: P (P&F)

EX250-SCA1A_eng

PWR P P 1 1 A A End plate SI unit Valve manifold Switch setting Before setting of Node-ID by DIP switch, turn OFF power supply to the SI unit. Safety Instructions Exchange of SI unit Remove screws from End Plate and release connection of each unit. Replace old SI unit with new one. (Tie-rod does not need to be removed.)

EX600-SEN_eng

Displays the diagnosis status of the unit. 10 to 57 Hz: constant amplitude 0.75 mm p-p 57 to 150 Hz: constant acceleration 49 m/s2 IP address is duplicated. Connection timeout. Connection is established. Recoverable error. The unit is in normal operation. The power supply for control and input is Off. The element in SI unit is broken. The power supply voltage for output is abnormal.

EX600-SEN3_4_eng

Settings1 Intermediate reinforcing brace (EX600-ZMB2) 10 to 57 Hz: constant amplitude 0.75 mm p-p 57 to 150 Hz: constant acceleration 49 m/s2 Mode Diagnostic size set for the input Content 2 Vibration resistance NOTE for 2 hours each in direction X, Y and Z respectively (De-energized) 0 OFF 0 byte Input data only (default setting) 147 m/s2 3 times each in directions of X, Y and Z respectively

EX600-SEN7_8eng

. : This switch can be enabled and disabled by parameter. 10 to 57 Hz constant amplitude 0.75 mm p-p 57 to 150 Hz constant acceleration 49 m/s2 for 2 hours each in direction X, Y and Z respectively (De-energized) Vibration resistance Diagnostic mode setting switch: Allocates the diagnostic data to the input data. Provide grounding to assure the noise resistance of the Fieldbus system.

EX600-SEC_eng

Tightening torque: 0.7 to 0.8 Nm. 10 to 57 Hz: constant amplitude 0.75 mm p-p 57 to 150 Hz: constant acceleration 49 m/s2 : Mode 3 is a function for extension in the future. (not to be used.) Vibration resistance After maintenance is complete, perform appropriate functional inspections. Stop operation if the equipment does not function properly.

EXxx-OMW0014CN

(EX245-EA2-1) No. 1 SI ON/OFF 2 IO-Link IO-Link 3 4 5 SI 6 . 1-1 12 No.EX-OMW0014CN-A 2. . 2-1 EX245 DC24 V 1 msec IP65(,) (IEC 60529 ) CE/UKCA UL(CSA) RoHS EN505812012 AC500 V1 FE 10 M -FE DC500 V -1050 -2060 35%85%RH 1057 Hz0.75 mm p-p 57150 Hz49 m/s 2 XYZ 2 (IEC60068-2-6) 147 m/s 2 XYZ 3 () (IEC60068-2-27) 13 No.EX-OMW0014CN-A 3. 3.1. 6 2M5( = 1.5 Nm