MHL2 that has a weight that is proportionate to the gripping force.
Set the operating pressure using the graphs as a guide.
Use a tightening torque of 0.05 to 0.1 Nm. As a rough guide, tighten the screw an additional 90 after feeling a tight resistance. As a rule, it should be turned about 90 beyond the point at which tightening can be felt. 0.5 0.2 0.3 MHL2-20D 0.5 0.2 0.2 MHC MHL2-25D 0.2 0.1 0.2 MHL2-32D 0.4 0.4 0.7 MHT MHL2-40D 0.2 0.4 0.7 MHY MHW MRHQ Misc.
Options Element sealing method Flat gasket (D.O.E) 1 N/A Bracket Quick plug Nil B P Housing material A square plug set is normally used for the drain unit. Cover SUS304 Case SUS304 Symbol 0 3 Quick Change Filter Series FQ1 Construction AIR VENT y Plug u O-ring w Cover INLET OUTLET t Element r O-ring e V-band i Upper element holder q Case o Lower element holder !
Open the sealed package inside a clean room. These products are packaged in sealed double packaging in a clean room. It is recommended that the inside packaging be opened in a clean room or other clean environment. 2. Flush out the piping. ITV IC ITVH ITVX Connect these products to piping only after it has been flushed and cleaned properly.
In the manifold specification sheet, specify the position where the block assembly is mounted. 13.1 3.4 Mounting hole Intermediate block assembly 2 (A) 2 (A) Clip 5 11.5 Gasket 4-11-14 Series S070 Exploded View of Separable Base Base mounted/SS073A-C Exploded View of Separable Base u i w r t q e !0 y !
Detaching To detach a socket from a connector, pull out the lead wire while pressing the sockets hook with a stick having a thin tip (about 1 mm). If the socket will be used again, first spread the hook outward.
(Pressure may be applied to any port : P, R, A) 4 Common Exhaust Valves can be ordered with a common exhaust port for the pilot and main valve.The Common exhaust provides for a cleaner operating environment by exhausting the pilot air through the main valve body rather than directly to atmosphere.
This regulator cannot be used as a check type regulator to be installed between a solenoid valve and an actuator. It can cause breakdown and malfunction. 7.
Do not use a load which generates surge voltage. The pressure switch output has a surge voltage suppressor, but it can be damaged if surge voltage is repeatedly applied. When the product is used to drive directly a load which generates surge voltage, such as a relay or solenoid valve, use a type with a built-in surge suppressor.
It is set to these values when delivered. 2.1 Communication Procedure This product receives a request message from the master computer and sends back a corresponding response message. It does not send a message firstly.
It is set to these values when delivered. 2.1 Communication Procedure This product receives a request message from the master computer and sends back a corresponding response message. It does not send a message firstly.
When the valve is exposed to a large amount of dust, install a silencer into the port 3(R). When dust enters the valve from the port 3(R), it may cause malfunction. Caution VH 1. Use in low temperature environments The valve can be used at a temperature down to 5C. Take appropriate measures to avoid freezing of drainage, moisture, etc. 2.
The type without the unit switching function will have a fixed SI unit (l/min, or l, m or m x 10). Output (OUT1) Indicator DOWN Button ( Button) Lights up when OUT1 is ON. UP Button ( Button) Use when decreasing a setting value. Use when increasing a setting value. MODE Button ( Button) SET Button ( Button) Use when changing a function. Use when selecting a function.
Upper 3 digits Lower 3 digits Reverse output Warning: + ON Time Part A should then be pressed in using a suitable tool, such as pliers. 2 sec. OFF Initialize mode DANGER indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury.
Caution: Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Warning: Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Danger : Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury. Warning 1.
A Groove position of auto switch B 1.8 1.6 Model MHK2-12 MHK2-16 A 10.4 12.8 B Standard switch grooves Dimensions A and B of other models are same as standard switch grooves. Contact P/A for the details on dimensions, specifications, and delivery time. 28
Options Element sealing method Flat gasket (D.O.E) 1 N/A Bracket Quick plug Nil B P Housing material A square plug set is normally used for the drain unit. Cover SUS304 Case SUS304 Symbol 0 3 Quick Change Filter Series FQ1 Construction AIR VENT y Plug u O-ring w Cover INLET OUTLET t Element r O-ring e V-band i Upper element holder q Case o Lower element holder !
2 t i q o !0 !1 i q o !0 !1 Component Parts No. Description Body A Handle Body B Needle Seat ring Needle guide Material Note No.
B C (EX600-ZT1) -15No.EX-OMN0027CN-D SI EX600-S A SI 1 PNP(-COM) 2 NPN(+COM) PR PROFIBUS DP No. 1 LED 2 3 4 (BUS OUT) 5 6 (PCI) 7 8 9 10 11 (BUS IN) 12 (2 ) (BUS OUTPCI) -16No.EX-OMN0027CN-D BUS IN BUS OUT 1 NC 2 RXD/TXD-N 3 NC 4 RXD/TXD-P 5 Shield T PROFIBUS DP BUS OUT SI IP67 PROFIBUS DP A [kbps] 9.6 19.2 45.45 93.75 187.5 500 1,500 3,000 6,000 12,000