PF-OMM0004_C [F 2] OUT2 e. ([ tPL]) [ tPH] or [ tnH] ([ tPH]) 4.
signal power supply 24V 13 CAL 14 E-STOP *1 *1 When the air servo cylinder is operated, turn ON the E-STOP signal.
AFF AMl Related poroducts Mounting Caution q Verify the direction of the flow of the compressed air and the e mark that indicates the inlet of the product before connecting.
Through-hole/CQ2YB, CDQ2YB Both ends tapped/CQ2YA, CDQ2YA Both ends tapped (mm) Bore size (mm) 63 O1 R O1 thread R R 18 M10 x 1.5 80 22 M12 x 1.75 100 22 M12 x 1.75 H thread effective depth C 4-N through 8-O counter bore U Q F 2-P (Port size) (Rc, NPT, G) I 22 M E D Z 11 Lead wire min. bending radius 10 Auto switch D-A7, A8 K M E S J L B + Stroke A + Stroke Rod end male thread H1 Rod end
e E , q 1.5 8 1 2 1 6 2 0 Cylinder speed (in/sec.) Sl6ct a propr unit sccording to exhaust flo/, in lh6 following ordr: (l) Oete|mine air con6umplion ot actuaicrs uaed in tl|e ckc\rii.
ZS-26-E-4 R04 4 plug-in reducer Connector for PSE300 1 pc.
r e Component Parts No.
e E , q 1.5 8 1 2 1 6 2 0 Cylinder speed (in/sec.) Sl6ct a propr unit sccording to exhaust flo/, in lh6 following ordr: (l) Oete|mine air con6umplion ot actuaicrs uaed in tl|e ckc\rii.
Maintenance Caution Model A B C D E Mounting dimension J H L K G F Port size Nominal size (B) ID200 240 240 320 320 1.
Table 3-3 Power supply cable and Earth Leakage BreakerRecommended Recommended earth leakage breaker Model Power supply Sensitivity voltage Cable qty. x size Rated Rated of leak voltage current current [V] [A] [mA] 1-phase 200-230V AC (50/60Hz) 3 cores x12AWG HRS040-A-20 200, Recomm 230 20 30 Terminal (3 cores x3.5mm2) HRS040-W-20 block ended (including ground) screw crimp diameter terminal
Table 3-3 Power supply cable and Earth Leakage BreakerRecommended Terminal block Recommended earth leakage breaker screw Recom Tightening Model Power supply Cable qty. x torque Rated Sensitivity Rated diameter mended voltage size voltag of leak current crimp e current [A] terminal [V] [mA] 3coresx12AWG 1-phase (3 cores 200-230V AC HRS050-A-20 200, x3.5mm2) (including 230 20 30 M4 5.5-4 1.5Nm
To minimize the voltage drop, use 100/200 V AC and 24 V DC wires with the largest sectional areas possible and keep the wiring length as short as possible. 5. The 100/200 V AC wire must not be bundled with or arranged in close proximity with the input/output lines of control terminals or encoder signal lines. If possible, keep a 100 mm or larger distance from such lines. 6.
Differential pressure indication switch r O-ring Applicable Applicable q O-ring w O-ring e O-ring Port size order no. hydraulic hydraulic order no. order no. order no.
OUTLET INLET Mounting hole Top view (Mounting hole on bottom) Porting Symbols OUTLET (Downstream) INLET (Upstream) 2PW 2PWA 2PWC q q q w 2 PORTS w w 3PWD 3PWE 3PWG 3 PORTS q q q e e e w w w 4PWM q e r 4 PORTS w 1114 A
[F 2] OUT2 e. ([ tPL]) [ tPH] or [ tnH] ([ tPH]) 4.
Table 3.8-2 RTU mode message frame a)Start b)Slave Address c)Function d)Data e) Checksum (CRC) f)End T1-T2-T3-T4 XX XX XX XX XX XX T1-T2-T3-T4 a) Start In Modbus RTU mode, message frames are separated by a silent interval (non-communication time).
To use the power of the product, the total load current must be 200 mA or less. 2.2 Communication specification HRLE Series 2-2 HRX-OM-Z015 Chapter 2 Contact input / output communication Table 2-4 Contact input/output communication terminal number PIN No.
12 Red 12 E 2 phase stepper motor PD Yellow 11 F 8 5 phase stepper motor For a signal power supply of 24VDC, connect an external resistor R (1.3k 1/2W) in order to hold the current to 15mA or lower.
12 Red 12 E 2 phase stepper motor PD Yellow 11 F 8 5 phase stepper motor For a signal power supply of 24VDC, connect an external resistor R (1.3k 1/2W) in order to hold the current to 15mA or lower.
SY114/SY124, SY114A/SY124A only. 2.1-6 Series SY100 Construction SY114, SY114A (A) 2 3 (R) 1 (P) q y e r w i SY SYJ VK VZ VT VT VP A R P o u t !0 !1 VG VP VQ VQZ Part No.