SI unit for AS-Interface The address at shipment from the factory is 0.
91tesl data Compact Guide Cylinder : Series MGO Bore size 0 12025I/MGQM12-25(Slide bearing) MGO[,|l2-2s 5 t ; .ioffi; '# ft til ; " 1 5 ' : r 6 0 E ; E ' l ! * 9 : 025 --l ,eln the machjne lype seleclion whn I dimsnsion becoms longer, selct the cylinclr hsvins a suflicient i. 020 \ Not t) when the cylinder i to be used ae a stopper use is at 30 stroke or les.
91tesl data Compact Guide Cylinder : Series MGO Bore size 0 12025I/MGQM12-25(Slide bearing) MGO[,|l2-2s 5 t ; .ioffi; '# ft til ; " 1 5 ' : r 6 0 E ; E ' l ! * 9 : 025 --l ,eln the machjne lype seleclion whn I dimsnsion becoms longer, selct the cylinclr hsvins a suflicient i. 020 \ Not t) when the cylinder i to be used ae a stopper use is at 30 stroke or les.
ImrUo\/ea cushion "Floating" cushion seal design eliminates piston rod "bouncing" due to cracking pressure at beginning of stroke. Compact and lightweight des n The square covers are made of an aluminum die casting and provide a lower cost, lighter weight product. ., .,'-., "'-, Accurate mounting~. .
T ype ;A .S C I ' D E F Y J ~ _L ~ " 4 15 9.5 14 4 4.5 6.5 7,5 ~ ZPlODQ Dl0 10 12 4 13 10,7 15 6 ::l 4 15 9.5 " ) L :l2 ~ 4 _'5 10 1~ ZP16DQ 016 16 18. '4 13, 11;.]11 1~ ,7 ZP4 ::l U40 4, 43 7 18 13.7 18.5 ZP25DO 025 25 28 4 15 15,5 20 10 I 0$0, I 50 53 7 18 14.7 ' 19.5 ZP40DO 0'\0 ,40 43 7 18 ~ "24.2 29 I .t~ lIE lndlcate malerlallo be selected at the end of part No.
The valve can be used at ambient temperatures as low as 20C, but take measures to prevent freezing or solidification of impurities, etc. 2. When used in cold areas, adopt freeze prevention measures such as draining the water from pipelines. If warmed with a heater, etc., avoid the coil unit.
The product is adjusted to each specification at the +24 V +24 V time of shipment from the factory. Do not perform unnecessary disassembly or removal of parts as it will cause failure. Output power Output power 0 V 0 V Control/Input power Control/Input power 7.
(Value at the initial state) Impact resistance Conditions when tested with a drop tester in the axial direction and at a right angle to the armature, one time each in energized and deenergized states. No malfunction occurred when tested.
When a pushing operation is performed at the maximum allowable set thrust at 100% duty ratio or more, stop (end) the operation within 10 seconds.
, ISE70/75 1/4" PT VERSION, INSTRUMENTATION, ISE70/75 PRESSURE SWITCH, DA, ISE70/75 1/4" PT VERSION, 0.46297 lb
Note 2) Vibration resistance No malfunction when tested with one sweep of 10 to 150 Hz in the axial direction and at a right angle to the armature, in both energized and deenergized states. Impact resistance No malfunction when tested with a drop tester in the axial direction and at a right angle to the main armature, one time each in energized and deenergized states.
<-III o ~ \ ~ r c-~~ ~ d" -, Rod end without L --' thread r~ \ A~OSW'tCh MM 8 NN LZ --' l S (Across H at) .. s .I w J 2051 3Gst 1561 I (mm) ,5 st lost ~ 1551 sst l. l0S" 20" 1.30>1. P .
Piping: NPT1/4, Output: 65 [PNP Open Collector 1 Output (Pin no.: 4)], Display Unit: -, Option 1: -, Option 2: -
Piping: NPT1/4, Output: 27 [NPN Open Collector 2 Outputs (Pin no.: 2,4)], Display Unit: -, Option 1: -, Option 2: -
Piping: NPT1/4, Output: 67 [PNP Open Collector 2 Outputs (Pin no.: 2,4)], Display Unit: -, Option 1: -, Option 2: -
Piping: NPT1/4, Output: 43 [NPN Open Collector 1 Output (Pin No.:4)+PNP Open Collector 1 Output (Pin no.:2)], Display Unit: -, Option 1: -, Option 2: -
Pressure Range: 0 to 1 MPa, Piping: NPT 1/4, Output Specification: Switch Output 1 + Switch Output 2 [NPN or PNP Switching Type], Unit Specification: -, Lead Wire: -, Bracket: -, Operation Manual/Calibration Certificate: -
, PRESSURE SWITCH, DIGITAL, INSTRUMENTATION, ISE70/75 PRESSURE SWITCH, DA, ISE70/75 1/4 PT VERSION, 1.00508 lb
, PRESSURE SWITCH, DIGITAL, INSTRUMENTATION, ISE70/75 PRESSURE SWITCH, DA, ISE70/75 1/4 PT VERSION, .53846 lb
, PRESSURE SWITCH, DIGITAL, INSTRUMENTATION, ISE70/75 PRESSURE SWITCH, DA, ISE70/75 1/4 PT VERSION, .99208 lb