SY3000/5000/7000 Series Plug-in Type Do not use in an environment where flammable gas or explosive gas exists. Usage may cause a fire or explosion. The products do not have an explosion proof construction. UL approved product Caution 5. Do not use in a place subject to heavy vibration and/or shock. When conformity to UL is required, the SI unit should be used with a UL 1310 Class 2 power supply.
It may cause injury to personnel. 5) Do not use the product to clean or remove toxic substances or chemicals. 6) Do not drop, step on or hit the product.
Do not use the drain tube in an upward direction. Do not bend or crush the drain tube. (Operation of auto drain will stop and water will flow out through the air outlet.) When tightening piping at the air inlet/outlet tube, the nozzle should be held firmly with a pipe wrench.
Do not use in these conditions. (Refer to specifications.) Consult SMC if a fluid other than compressed air is used. 2.
Safety Instructions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
For details, refer to 3 point preset counter/CEU1 on page 10-12-30, and Multi counter/CEU5 on page 10-12-27 respectively.
2 8 A Stacking type 10 3/8" 10 3/8" Manifold stations 10 3/8" 10 3/8" 02 2 stations 3 3 12 1/2" 12 1/2" 05 5 stations 12 1/2" 12 1/2" LQ2 integral fitting 4 4 19, 3/4" 19, 3/4" How to Order Valve LVH 2 0 07 A S Body class Symbol 2 3 4 Body class 2 3 4 Orifice dia.
Do not use exceeding the value shown by the graph.
For details, refer to 3 point preset counter/CEU1 on page 10-12-30, and Multi counter/CEU5 on page 10-12-27 respectively.
Tighten others with 0.60.05Nm. -27- 12. Domensions 12-1.
Port size VCW2 VCW20-12-01 1/8, 1/4 VCW30-12-02 1/4, 3/8 VCW3 VCW30-12-04 1/2 VCW40-12-02 Series 1/4, 3/8 VCW4 VCW30-12-04 1/2 2 3 4 Class 2 Class 3 Class 4 VCW40-12-06 3/4 Bracket material: Stainless steel Valve type Material and insulation type N.C.
Do not use in a location having an explosive atmosphere. 2. Do not operate in locations where vibration or impact occurs. 3. Do not use in locations where radiated heat will be received from nearby heat sources. Maintenance Warning 1. Maintenance should be performed in accordance with the procedures in the Operation Manual.
Do not apply excessive lateral loads to the piston rod.
Valve model Port size VCS21 VCS20-12-01 1/8, 1/4 34 40 25 30 12.8 12.8 5 4.5 6 13 VCS30-12-02 1/4, 3/8 42 52 30 40 19 19 6 5.5 7 19 VCS31 VCS30-12-04 1/2 48 56 36 44 23 23 6 5.5 7 23 VCS40-12-02 1/4, 3/8 42 52 30 40 23 23 6 5.5 7 19 VCS30-12-04 VCS41 1/2 48 56 36 44 23 23 6 5.5 7 23 VCS40-12-06 3/4 56 65 44 53 28.2 28.2 6 5.5 7 26 Bracket material: Stainless steel 3 Series VCS Direct Operated
Do not use liquids that will cause the wetted sealant to swell.
Regulator and filter regulator 1) Be sure to unlock the handle before adjusting the pressure and to lock it after the pressure is set. 2) During transport and installation, do not apply shock to the product, such as by dropping doing so will affect its precision. 3) Do not install it iin an area that is exposed to high temperature or humidity, because doing so will lead to improper operation
Note Do not pressure-weld the connector cover at the edges. Do not pressure-weld the connector cover at the back of the pressure welding block.
Compressor breaker trip2 13 Compressor inverter error 14 Pump breaker trip2 15 Pump inverter error 1: These alarms do not occur on the product of the cooling method -W. 2: These alarms do not occur on the product of the power specification '-20'.
Do not apply grease to the piston rod. There is a danger of sharply reducing the locking performance. For normal operation, remove the manual unlocking bolt. It will cause lock malfunction. 3. 20 to 32, a 12 silver seal is labeled on the one surface of the lock body (on the surface opposite from the unlocking port).
Do not apply grease to the piston rod. There is a danger of sharply reducing the locking performance. For normal operation, remove the manual unlocking bolt. It will cause lock malfunction. 3. 20 to 32, a 12 silver seal is labeled on the one surface of the lock body (on the surface opposite from the unlocking port).