Title not found I W h s i r l Black o-Y69A.Y6gB.O-Y7PV D-Y598.Y698/2 wire system l " ' . . r 6 7 7.5 I 8.5 1--&9p9!9q E!
Hydraulic fluid Compatibility Standard mineral hydraulic fluid Compatible W/O hydraulic fluid Compatible O/W hydraulic fluid Compatible Water/Glycol hydraulic fluid Phosphate hydraulic fluid Not compatible Consult with SMC. 265 A CHKD Series Theoretical Output Unit: N Operating pressure (MPa) Bore size (mm) Rod size (mm) Operating direction Piston area (mm2) 10 3.5 7 314 3140 1099 2198
ON/OFF, with load (ON:OFF=3:1)W A variety of single/double modular configurations is possible.
For actuators with external stopper, the rotation end can be set within the ranges shown in the drawing by adjusting the stopper bolt. c l o r c e k t n w u i s o e c B port A port e c s l o i w c k Basic type For 90 and 100 For 180 and 190 Single flat Single flat +8 0 +10 0 90 0 or 10 B port A port B port A port t f fla or t f le fla ng si le ng of e si ng of ra n ge io +8 0 at an ot R
5 w o !0 i e r y !3 !4 @0 !9 t !8 @2 @4 !
Grommet type (G) Rated voltage DIN terminal (D) Part no. symbol W/o indicator light With indicator light W/o indicator light With indicator light W/o indicator light With indicator light No.1 Coil Coil S Varistor Varistor No.2 AC No.1 Varistor Neon light None Coil Z How to Calculate the Flow Rate No.2 No.1(+) Caution Red(+) For obtaining the flow rate, refer to front matter.
Configuration 1 master : 1 thermo-chiller 2 2 R D R D 3 3 S D S D 5 5 S G S G Master This product Do not connect any wire to other PIN numbers. Fig. 3-11 Connection of RS-232C 3.3 Installation HRS Series 3-16 HRX-OM-R005 Chapter 3 Transport and Setting Up 3.4 Piping Connect piping firmly.
/s Piston speed mm/s Piston speed mm/s 4 Series CY1F Vertical Actuation qVertical operation In vertical operation, observe the maximum load mass and the maximum operating pressure shown in the table below to prevent a drop due to slipping off of magnet couplings.
Connect the motor power supply input terminal (U, V, W) to the driver power terminal (U, V, W).
Female lhread length {"1') is shonerfor the lollowing . 2o0 (2') 1/g & 1A st. 1/s & 1/a st. r/s & 1/a st. l=o.44 25O (2112')' I/s st. r/s st. '/s stl=0.44 300 (3") ]/s & 1/a st. 1/e &r/l st. 1/e & 1A st. 400 (4) 1/s &1/a st. r/s & 1/a st. 1/e &14 st. Series NCQT Dimensions Spring Extend NCQTBO-OT T Type Bore,, 9t4,F' I 60re ,b,:!
After 1.6 s Blinking After 0.2 s When an alarm or warning also occurs during the test operation, the decimal point on the first digit will blink as follows. After 0.8 s After 0.8 s Blinking Blinking After 0.2 s (4) Start operation with the PC. -21- 5.2 JOG Mode JOG operation can be executed without host command.
Configuration 1 master : 1 thermo-chiller 2 2 R D R D 3 3 S D S D 5 5 S G S G Master This product Fig. 3-11 Connection of RS-232C 3.3 Installation HRS Series 3-16 HRX-OM-W038 Chapter 3 Transport and Setting Up 3.4 Piping Connect piping firmly. Incorrect piping might cause leakage of supplied or drained leakage and wet surrounding area and facility.
t o u i Resin materials eliminated Laser marking is employed for the model designation. d t o o g e a n L c 2 s u s d Particulate generation has been reduced at the stroke ends by reducing impact using a sine cushion and by stopping the stroke using an internal stopper. i e Reduction of outgassing due to surface treatment n Impact acceleration [m/s2] o u d t R g g e a c 1 s u s d 5 i e n
valves there is no S option.
Example using a 20[mm] Lead Actuator with target travel speed of 500[mm/sec] Rotations per second Travel distance per second Travel distance per rotation Rotation Speed (rpm) = {Speed (mm/s) Lead (mm) }60 (S) = {500 (mm/s) 20 (mm) }60 (s) =1500 (rpm) The rotation speed must be a value between 0 and the allowable actuator speed. The actuator will not operate if set to 0.
Configuration 1 master : 1 thermo-chiller 2 2 R D R D 3 3 S D S D 5 5 S G S G Master This product Do not connect any wire to other PIN numbers. Fig. 3-11 Connection of RS-232C 3.3 Installation HRS Series 3-16 HRX-OM-O021 Chapter 3 Transport and Setting Up 3.4 Piping Connect piping firmly.
Characteristics Maximum piston speed: 500 mm/s It can be used at 50 to 500 mm/s provided that it is within the allowable kinetic energy range. Air cushion is standard. Enables the impact to be absorbed at the stroke end when the cylinder is operated at high speeds. Cylinder position can be detected.
Characteristics Maximum piston speed: 500 mm/s It can be used at 50 to 500 mm/s provided that it is within the allowable kinetic energy range. Air cushion is standard. Enables the impact to be absorbed at the stroke end when the cylinder is operated at high speeds. Cylinder position can be detected.
2 u r e q w No. q w e r t y u i o !0 !1 !2 !3 !4 !5 !6 !7 !8 !
for purge air discharge (Option: P) u t e q IN OUT i } r w y HA Purge air for dehumidification Purge air for dehumidification AT ID AMG Component Parts AFF Material Description No.