Safety Instructions Use a straight bladed watchmakers' screwdriver for the set trimmer to turn it softly. Use a straight bladed watchmakers' screwdriver to adjust the set trimmer for I(Z)SE1/I(Z)SE2/PS100. Turn it softly, but do not turn more when reached to the stopper at both ends. If a trimmer were broken, it would be impossible to adjust it. 6.
[Horizontal and lateral mounting] A B SOL.3 W RE A B A magnetic field of 14.5 mT is equivalent to a position that has about 18 cm radius from a welded part using about 15,000 amperes of welding amperage. When using it in a stronger magnetic field, cover the sensor with magnetic and shield it.
MY-SA 2-G F E 2-H C D A B Side support B MY-SB 2-J C D A B (mm) A 61 70 87 B 75 84 105 C D E F G H J Part no.
Front Structure of the product number W R 0001 (2018 April) W R 0001 Year Symbol Note Month Symbol Note Serial No. 2018 2019 2020 2021 W X y Z Repeated from A to Z in alphabetical order 1 2 3 4 o P Q R Repeated from A to Z in alphabetical order, with o assigned for January and Z for December. 1.2 Hazard classifications/ Hazard Warning Labels IDFC60/70/80/90 Series 1-4 IDX-OM-U010 Chapter
When a surge generating a load such as a relay or solenoid is directly driven, use a type of switch with a built-in surge absorbing element. 4. Since the type of fluid varies depending on the product, be sure to verify the specifications. The switches do not have an explosion proof rating. To prevent a possible fire hazard, do not use with flammable gases or fluids. 5.
This produces an air cushion cylinder which retains the merits of a compact design. Operating principle q When the piston is retracting, exhaust is discharged from both A and A' until piston seal H passes the air passage A. A + A' A' w After piston seal H has passed the air passage A, exhaust is discharged only from A'.
At piping This is equivalent to a magnetic field of approximately 18cm in radius from a welding area using a welding current of almost 15,000 amperes. To use the system in a magnetic field that exceeds this value, use a magnetic material to shield the sensor unit Foreign matter should not enter. Entering of foreign matter will cause malfunction.
Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com E depth EK Q + Stroke Z + Stroke A G Stroke adjustment screw Note 3) (inner cover) Plug Plug [P (port e)] [P (port c)] A A LW Plug Operating direction P (port a) P (port b) Auto switch mounting groove [P (port g)] 0.5 Note 2) 0.5 Note 2) Left Right Plug [P
Nominal size (Torque) For 1 piece, a right hand auto switch is installed.
MY-SA 2 x G F E 2 x H A B C D Side support B MY-SB 2 x J A B C D A 61 70 87 B 75 84 105 C D E F G H J Part no.
: 13 SY1l4 (A): 24 SY1l3 (A): 15 SY1l4 (A): 26 3 4 0 to 0.7 SY11 A 100kPa to 0.6 100kPa to 0 N.C.
P/A as a contact protection box may be necessary.
Actuator drive When an actuator, such as a cylinder, is to be driven using a valve, take appropriate measures to prevent potential danger caused by actuator operation. 2. Effect of back pressure when using a manifold Use caution when valves are used on a manifold, as actuator malfunction due to back-pressure may occur.
When a surge generating a load such as a relay or solenoid is directly driven, use a type of switch with a built-in surge absorbing element. 4. Since the type of fluid varies depending on the product, be sure to verify the specifications. The switches do not have an explosion proof rating. To prevent a possible fire hazard, do not use with flammable gases or fluids. 5.
Devise a safe system so that if a person engages the emergency stop or if a safety device is tripped during a system malfunction, such as a power outage, the operation of the magnet gripper will not cause a hazard to humans or damage the equipment. 7. Consider the action when operation is restarted after an emergency or abnormal stop.
A Round head combination screw M3 2 1 + "+" mark "" mark A Round head combination screw M3 Conduit terminal View A-A (Internal connection diagram) There is polarity only when equipped with light.
Never mount a switch in a place that will be used as a scaffold during piping work. Damage may occur if subjected to an excessive load. Especially when the switch supports piping, do not apply a load of 15Nm or more to the metal part of the switch. 11. Provide a section of straight pipe of at least 8 times the pipe diameter in the piping before and after a switch.
Therefore, make sure to use a pressure regulator to convert line pressure into supply pressure for the actuating valve and the brake valve. In order to actuate multiple cylinders at once, use a pressure regulator that can handle a large air flow volume and also consider installing a surge tank.
use a watchmakers screwdriver with a handle diameter of about 5 to 6 mm.