Digital Pressure Switch For heavy stains, use a cloth soaked with diluted neutral detergent and fully squeezed, then wipe up the stains again with a dry cloth. -8No.PS-OMH0003-F Model Indication and How to Order For Air : I S E For Fluid : I S E Option Indications Pressure specification 70 0 to 1 MPa 02 43 M S 70 02 43 A 75H L M Pressure specification Option 2 75 0 to 10 MPa Nil No option 75H 0 to 15 MPa A Bracket
When a system hazard can be expected due to a drop in vacuum pressure caused by power loss or vacuum pump trouble, install a safety circuit and configure the system so that it can avoid the danger. 2. When a system hazard can be expected with a malfunction of the vacuum regulator, install a safety circuit and configure the system so that it can avoid the danger. 1.
Bottom Straight S No bracket S IN 1 IN Made to Order Output specifications V T OUT1 OUT2 A B C D E With panel mount adapter (For with flow adjustment valve) With panel mount adapter (For without flow adjustment valve) NPN PNP NPN NPN PNP PNP NPN PNP NPN PNP Analog 1 to 5 V Analog 4 to 20 mA Analog 1 to 5 V Analog 4 to 20 mA External input Note) Panel mount adapter A ZS-33-J ZS-33-JS Panel
A new security code can now be entered. 3. Enter a new security code. The first digit will start flashing. Press the or button to select a value. Press the button to set, and the next digit to the right will start flashing. If the S button is pressed at the last digit, the first digit will start flashing. 4.
Bracket A (Part No.: ZS-50-A) Bracket B (Part No.: ZS-50-B) -13No.PS-OMW0002-C Piping Piping specification: -02 and -N02 After hand tightening, tighten the fitting using a spanner on the flat surfaces of the fitting. The tightening torque must be 8 to 12 Nm. Piping specification: -F02 After hand tightening, tighten the fitting using a spanner on the flat surfaces of the fitting.
Caution Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Warning Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Danger Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury. Warning 1.
Body Size: -, Thread: -, Port: -, Option: -, Attachment: -, Semi-Standard 1: -, Semi-Standard 2: -
Due to the compressibility of air as a fluid, the actuator will continue to move until it reaches a position of pressure balance, even though the pilot check valve closes with an intermediate stop signal. 2. This product cannot be used to hold a stop position for an extended period of time. Pilot check valves and actuators are not guaranteed for zero air leakage.
Realizes momentary intermediate stoppage of a cylinder and able to adjust speed control of it. Tubing mount direction is 360 free. Electroless nickel plated is provided as standard. Applicable tubing O.D.
I f a p re s s u re g re a t e r t h a n t h e s e t p re s s u re i s re a c h e d , t h e u n i t w i l l o p e n , c l o s i n g w h e n p re s s u re i s l e s s t h a n s e t pressure.
(Total Travel) From free position to total travel position I f t h e s e v a l v e s a r e u s e d f o r g u a r d i n g o r s a f e t y i n t e r l o c k s y s t e m s , i n s t a l l a t i o n a n d application should be as per BS5304: 1988.
/S (8 points output) R2 09 9 Can accommodate up to 16 solenoids.
An appl i cat i on w hi ch has t he possi bi l i t y of havi ng negat i ve ef f ect s on peopl e, propert y, or ani m al s requi ri ng speci al saf et y anal ysi s. 2 H andl i ng precaut i ons CAU TI O N I f pow er t o t hi s product i s cut of f due t o a pow er f ai l ure, et c. w hen i t i s i n a cont rol l ed st at e, resi dual pressure w i l l be ret ai ned t em porari l y.
(Normally closed) A N.O.
And, when the sensitivity is changed to dull, there is a possibility that staggering of gradual pressure occur, because the pressure correction become lower. No Key operation LED Display (1) Deactivate the key lock if necessary (see page 22). (2) Press S-key for 2 seconds or more, then go to detail setting mode. (3) To "F02" by using the and keys.
W hen t he sensi t i vi t y i s changed, t he correct i on operat i on of pressure changes. W hen t he sensi t i vi t y i s changed t o sharp, t he hunt i ng of pressure m i ght be occurred. And, w hen t he sensi t i vi t y i s changed t o dul l , t here i s a possi bi l i t y t hat st aggeri ng of gradual pressure occur, because t he pressure correct i on becom e l ow er.
Caution Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Warning Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Danger Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury. Warning 1.
Example of Improvement Review the air-blow job and change to the SMC blow gun, S coupler and coil tube to create a larger effective area.
Power is supplied S S S SET (S) button Press this button to change the mode and to set a value. L Press the S button for 2 seconds or longer. DOWN () button Selects the mode and decreases the ON/OFF set value. M Setting F0 Setting F1 Setting F99 N Indicates the unit currently selected. Unit display The output will not operate for 3 seconds after supplying power.
Output deviation factor (% F .S.) 0.6 0.5 0.4 Return 0.2 0 0 0.2 0.4 0.5 Out 0.6 0.8 0 25 50 75 1 1 2 3 4 1 5 100 Input signal (%F .S.)