ZP Pad Caution Guide for drop prevention Provide an auxiliary device (example: a guide for preventing the workpieces from dropping) as necessary. Mounting Position As a rule, the unit must be installed horizontally.
Thus, if a load is applied, the piston rod will not be able to retract to the end of the stroke. 4. In the case of a single acting cylinder, a breather hole is provided in the cover surface. Make sure not to block this hole during installation, as this could lead to a malfunction. 5.
used as a stopper, select a model with 30 mm stroke or less.
A Dimensions except A, L and L1 are the same as rod side flange style.
Pad Caution Guide for drop prevention Provide an auxiliary device (example: a guide for preventing the workpieces from dropping) as necessary. Mounting Position As a rule, the unit must be installed horizontally.
in the figure below, this pilot-operated solenoid valve consists of a compact 3 port solenoid valve as the pilot valve and a large 3 port valve as the main valve.
Dedicated grounding should be used as much as possible. Grounding should be to a type 3 ground. (Ground resistance of 100 or less.) 3. Use a wire with a sectional area of 2 mm2 or larger for grounding. Grounding should be as close as possible to the controller, and the ground wires should be as short as possible. 4.
as a stopper, select a model with a stroke of 50mm or less.
As a result, it is necessary for the customer to verify final EMC conformity for the machinery and equipment as a whole. Caution Maximum speeds of actuators vary depending on the type.
Suction filter To protect the ejectors and valves from dust, the use of a suction filter (Series ZFA, ZFB) is recommended. 5. Use of a vacuum switch It is recommended that verification be made with a vacuum switch as much as possible. 6. Vacuum release valve To serve as a vacuum release valve, use a 2 port or 3 port valve.
" A A 1/4" B B 1/4" B B 3/8" The table of combination is the same as that for A side.
Locked position S0700 VQ PUSH LOCK VQ4 Series SY3000/5000/7000/9000 Used as a 3-Port Valve VQ5 Caution Caution VQC In case of using a 5-port valve as a 3-port valve When operating the locking type D with a screw driver, turn it gently using a watchmakers screw driver.
Pad Caution Guide for drop prevention Provide an auxiliary device (example: a guide for preventing the workpieces from dropping) as necessary. Mounting Position As a rule, the unit must be installed horizontally.
29 11 11 5.1 5.1 9.5 9.5 B H A 26 10.5 26 10.5 (NN 1) x H G Section AA Section BB (mm) Model F 45 40 48 58 42 55 50 55 62 N 4 4 4 4 6 6 8 8 8 G 22 22 22 22 17 18 37 56 H 46 46 46 56 56 56 59 62 NN 2 2 2 2 3 3 4 4 4 GA 18 18 18 22 48 73 74 96 118 HA 50 50 50 56 48 56 112 118 124 I 16 16 16 16 18 23 25 18 21 J 46 46 46 56 72 100 155 190 215 K 31 41 51 61 71 96 121 146 171 KA 126 183 211
Use the table as a guideline for mounting.
Auto switch mounting Auto switch model C85 Series C75 Series Bore size [mm] 8 10 12 16 20 25 32 40 D-M9l(V) D-M9lW(V) D-A9l(V)*7 BJ6-008 (A set of a, b, c, d) BJ6-010 (A set of a, b, c, d) BJ6-012 (A set of a, b, c, d) BJ6-016 (A set of a, b, c, d) BM5-020 (A set of a, b, c, d) BM5-025 (A set of a, b, c, d) BM5-032 (A set of a, b, c, d) BM5-040 (A set of a, b, c, d) D-M9lA(V) BJ6-008S (A
as a bracket, those parts are to be assembled at the time of shipment.
steel Only when using nickel plating, tube cover 33 Cushion valve Rolled steel Electroless nickel plating 34 Valve retainer Rolled steel Electroless nickel plating 35 Lock nut Rolled steel Nickel plating 36 Cushion seal A Urethane 37 Cushion seal B Urethane 32 or larger: Same as A 38 Cushion ring gasket A NBR 39 Cushion ring gasket B NBR 32 or larger: Same as A 40 Valve seal NBR 41 Valve