Battery-less LEC-CN5-m To Parallel I/O connector Actuator cable*1 p. 178 Robotic cable LE-CE-m To SI To ENC 1 Can be included as an option. Refer to the How to Order page of the actuator.
Note 13) For an actuator with lock, add the power consumption for the lock. Note 1) Please consult with SMC for non-standard strokes as they are produced as special orders. Note 2) The maximum value of the horizontal work load. An external guide is necessary to support the load. The actual work load changes according to the condition of the external guide.
Do not use in an environment with temperature cycles. Consult SMC if switches are used where there are temperature cycles other than normal air temperature changes, as they may be adversely affected. 6. Do not use in an environment where there is excessive impact shock.
Do not use in an environment with temperature cycles. Consult SMC if switches are used where there are temperature cycles other than normal temperature changes, as they may be adversely affected. 6. Do not use in an environment where there is excessive impact shock.
Intermediate stopping of load with an air pressure circuit When stopping a load using an air pressure circuit, operate at or below the kinetic energy shown in the table below. Use caution, as operation when exceeding the allowable value can result in breaking of the magnetic coupling.
Remove the covers as shown in Figure 2 and make further adjustment by loosening the hexagon nut. 3. Various dimensions are indicated in Table 1. Never make an adjustment that exceeds the dimensions in the table, as it may cause an accident and/or damage.
If you stop pulling the bolt, the lock will return to an operational state. Thread sizes, pulling forces and strokes are as shown below.
The position of spanner should be a root as close as possible to R thread. Hex. across flats may be deformed, if using an improper wrench for hex. across flats.
[An asterisk () indicates those that are the same as standard.]
When it is necessary to operate it as an ordinary double acting cylinder at an even lower operating speeds, use a low speed cylinder (refer to Made to Order on page 6-17-19).
Use caution, as operating above the prescribed values may lead to dropping of the load. The cushion effect (smooth start-up, soft stop) exists only before the stroke end in the stroke ranges indicated in the table below. The cushion effect (smooth start-up, soft stop) cannot be obtained in an intermediate stop or return from an intermediate stop using an external stopper, etc.
Use caution, as operating above the prescribed values may lead to dropping of the load. The cushion effect (smooth start-up, soft stop) exists only before the stroke end in the stroke ranges indicated in the table below. The cushion effect (smooth start-up, soft stop) cannot be obtained in an intermediate stop or return from an intermediate stop using an external stopper, etc.
This product cannot be used as a check regulator by installing it between solenoid valve and actuator. 3. Port with a pressure gauge or a plug can be used as an OUT port.
Pad Caution Guide for drop prevention Provide an auxiliary device (example: a guide for preventing the workpieces from dropping) as necessary. Mounting Position As a rule, the unit must be installed horizontally.
Note 3) When n is an odd number, an even number that is one larger than this odd number is used for the calculation.
How to Order Type 46 (5 port/Base mounted) 10 SS5YJ3 46 05 M5 Type 46 Type S46 ( ) Single solenoid pilot valve is on same side as the A, B port. Clean series CE-compliant M5 x 0.8 R1, R2 port Stations Nil 02 2 stations Valve mounting direction P port thread type Q CE-compliant : : Single solenoid pilot valve is on opposite side as the A, B port.
For an exterior dimension diagram to identify the mounting support types, refer to p.3.1-21 to 3.1-24 as the dimensions are identical to those of standard.
Note) When placing an order for body ported solenoid valve as a single unit, mounting bolt for manifold and gasket are not attached. Order them separately, if necessary.
This allows reading and monitoring the contact signal from an external switch. When inputting an external switch signal to the contact input, select External Switch (external switch signal) for the type of contact input signal. (Refer to 2.3.1 Setting of contact input signal type and form) If an input from an external switch is detected, it can be generated as an alarm.