Title not found

a a a o a o a a a a o a a a a o a a a a a a o a a a i a a a a a a a a a a a a a a a a a a a a a a a a a a a r a a a a a a o a o a SMC Offers the Highest DimensionalAccuracy .

0.4

B A B A B A B A A A PWR 93.5 COM (35) 64.4 43.2 66 75 (40) series EX500 2 9 SI unit 4 x M4 mounting hole 8 7 6 5 4 3 2 1 n D side Stations U side C8 [3(R) EXH port] C8: 8 One-touch fitting M12 8-pin socket DIN rail clamp screw R R 0 62.5 3 3 60 1 X X 40.5 B B B B B B B B 12 12 22.2 P P 25 1 1 A A A A A A A A 18.5 7.5 9.5 (12) (7.5) M12 8-pin plug C8 [1(P) SUP port] C8: 8 One-touch fitting

VQC

SUP block plate VVQ2000-16A EXH block plate VVQ2000-19A Port plug Note 1) A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B C4 (N3) With 4 (5/32") One-touch fitting Side port Cylinder port sizes Fill out in case of mixed sizes (CM/LM/NM).

Plug-in Unit

override Indicator light 65.5 P=25 A A A B A B A B A B A B 21 21 63 9 A A A A A A A 143 163 66 41.5 9 B B B B B SI unit Input block 10 n 1 2 3 4 5 6 7 Stations D-side 8 U-side Formulas L1 = 25n + 106 (Maximum 16 single wiring stations) L2: For one input block.

Table of Contents

L4 L4 L5 A L5 D3 D3 T T D2 L1 D2 L1 L2 L2 AS ASP Metric Size ASN A M1 L5 Max.

New

1A VXN Z 1 2 A A Enter standard product number.

Digital pressure switch for energy-saving control ejector

CAUTION indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Caution : WARNING indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Warning : DANGER indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury.

5 Port Solenoid Valve, Series VQC

A Station 1 1 SOL. A Station 2 14 SOL. A Station 3 2 1 SOL. A Station 4 14 15 2 SOL. A 15 3 3 4 5 6 7 Station 5 16 17 18 19 20 SOL. B 16 SOL. A 4 Station 6 SOL. B 17 SOL.

Digital pressure switch for energy-saving control ejector

due to a new measurement law.

Pressure switch for energy-saving control ejector with N.O. type valve

Check if the load is short circuited. (3) Check if a relay without a surge (3) Use a relay with a surge voltage suppressor or take measures to prevent noise.

Digital pressure switch for energy-saving control ejector

This can be prevented by inserting a noise filter, such as a line noise filter and ferrite core, between the switch-mode power supply and the product, or by using a series power supply instead of a switch-mode power supply.

5 Port Air Operated Valve

(EA)5 1 (P) 3(EB) u i 3 position pressure center 3 (EB) 2 (B) 1 (P) 4 (A) 5 (EA) 2(B) (A)4 (EA)5 1 (P) 3(EB) (Drawing shows a closed center type.)

ZK2-C

No.13 No.14 A No.15 -46NO.ZK2-OM00801-B No.

ZQ-OM01601

(A-B)/4 A= H_1=|(A-B)/2| B= 1 28 - [F 6] 5R.D. <> [F 6] [FSC] 1 [F 6] 29 - [F11] <> [F11] , 1000 100 [F11] [MPa]/[kPa]/[kgf/cm 2]/[bar]/[psi]/[inHg] 2]/[bar]/[psi]/[inHg]:) ([kgf/cm 21 -[F 0] 30 - [F80] 30 ,OFF <> [F80] 1 2 2 1 [F80] 1,OFF 1 2,30 () 2 OFF ON 31 - [F81] , <> [F81] [F81] , 000 40 32 - [F90] <> [F90] [on] [oFF] 1 [oFF]() 2 [F90] 1 34

IZ-OMU0031-CN

ZS-28-C 37104-3101-000FL 1-1473562-4 A 1 (DC+) 2 3 (DC-) 4 (IN15 V) A A (FG) -11No.IZ*-OMU0031 DC(+) 5 OUT1 4 OUT2 3 2 DC(-) 1 -12No.IZ*-OMU0031 ()(ZS-28-A) IZE110 DC(+) () NPN2 Max.30 V80 mA 1 V 15 V 1 k () OUT1 () OUT2 () DC(-) () DC(+) IZE111 () NPN2 Max.30 V80 mA 1 V 420 mA 600 (DC24 V) 50 () OUT1 () OUT2 () DC(-) () DC(+) IZE112 () PNP2 Max.80 mA 1 V 15 V 1 k

Series 10-SV1000/2000/3000/4000 5 Port Solenoid Valve

3/5 3/5 4 A 4 A 4 A 4 A 2 B 2 B 2 B 2 B 2 B P 1 P 1 One-touch fitting [1(P), 3/5(E) port] Applicable tubing O.D.

HRX-OM-W002

For a facility having a large installation area (that can vent the air naturally): Make an air outlet on a wall at a high level and air inlet on a wall at a low level, to allow for adequate airflow. 2. For a facility having a small installation area (that can not vent the air naturally): Make a forced air exhaust vent on a wall at a high level and an air inlet on a wall at a low level.

HRX-OM-X071

For a facility having a large installation area (that can vent the air naturally): Make an air outlet on a wall at a high level and air inlet on a wall at a low level, to allow for adequate airflow. 2. For a facility having a small installation area (that can not vent the air naturally): Make a forced air exhaust vent on a wall at a high level and an air inlet on a wall at a low level.

HRX-OM-X084

For a facility having a large installation area (that can vent the air naturally): Make an air outlet on a wall at a high level and air inlet on a wall at a low level, to allow for adequate airflow. 2. For a facility having a small installation area (that can not vent the air naturally): Make a forced air exhaust vent on a wall at a high level and an air inlet on a wall at a low level.

LV50-OMQ0002

Never mount the product in a place that will be used as a scaffold during piping.