PFxx-OMJ0005CN

10(5) PFM710--D/F 10(5) PFM725--C/E 25(12.5) PFM725--D/F 25(12.5) PFM750--C/E 50(25) PFM750--D/F 50(25) PFM711--C/E 100(50) PFM711--D/F 100(50) ( )CO2 ( ) CO2 () 25[L/min] 10[L/min] [L/min] [L/min] 50[L/min] 100[L/min] [L/min] [L/min] -57No.PF-OMJ0005CN-I (350[kPa]) 25[L/min] 10[L/min] [kPa] [kPa] [L/min] [L/min] 100[L/min] 50[L/min] [kPa] [kPa] [L/min] [L/min] -58No.PF-OMJ0005CN-I

PF-OMM0004_C

[F 2] OUT2 e. ([ tPL]) [ tPH] or [ tnH] ([ tPH]) 4.

HRX-OM-M090

Plug (Prepared by customer) L N E [Accessory] Power supply connector N E Earth leakage breaker (Secondary side) L N Cable Crimped terminal (Prepared by customer) E (Earth) L Cable size : 14AWG Wire tightening torque : 0.5Nm Fig. 3-5 Power supply cable 3.3 Installation HRS Series 3-10 HRX-OM-M090 Chapter 3 Transport and Setting Up Wiring 1.

K35-OMX0029

signal power supply 24V 13 CAL 14 E-STOP *1 *1 When the air servo cylinder is operated, turn ON the E-STOP signal.

Rotary Table

The end angular speed is obtained by: t Table 9 Allowable kinetic energy (J) Size Allowable kinetic energy : Rotation angle [ rad ] : Rotation time [ s ] 1 0.001 Kinetic energy E is obtained by: 2 0.0015 3 0.002 7 0.006 E Therefore, the rotary table rotation time is: E: Allowable kinetic energy [ J ] : Rotation range [ rad ] I: Moment of inertia [ kgm2 ] During uniform acceleration, the

Electric Slide Table / High Precision Type 《 AC servo motor 》

Vertical line of belt teeth Flaw which is made when the belt runs on the flange. e. Rubber back of the belt is softened and sticky. f. Crack on the back of the belt 4. Troubleshooting Alarms below are abstract of representative examples.

ML1C

Applicable bore Shock absorber model ML1-A25H ML1-A32H ML1-A40H ML1C25 ML1C32 ML1C40 101 90 25 20 11 72 67.3 12 31 39.5 Max. 16.5 4.5 3 RB1412 120 107 30 25 16 93 73.2 15 38 49 Max. 20 5.5 6 RB2015 147 129 30 31 16 105.5 73.2 15 40.5 54.5 Max. 25 5.5 6 Side Support Side support A 2 x G E E F 2 x H A B Side support B 2 x J A B (mm) A B C D E F G H J Part no.

3-Position Rotary Table

MSQ Angle adjustment Range Figure 5 MSZ MSZ CRQ2X MSQX ad a ge ju Cl lt MRQ an st bo oc t r m nd en g k en tm wi in e us 10 10 se t r st on dj a ju an r on ti ot ad iti ta os ge at p ro er y nt io e b C e b n y is e ge n ad w d k an c ju lo t r C st in en g m bo st lt ju b ad M 0 ax 19 im e u ng m ra ro n ta tio Center position adjustment Table 2 R: Clockwise adjustment L: Counterclockwise

0.01

ID Construction IDG SFD101-02 SFD102-02 IDK w q r t e q r e w AMG AFF AM AMD AMH Component Parts Component Parts No. Description Note Material Aluminum alloy No.

CUJ

3 w e q !1 r y o e t !2 For 4 Built-in magnet Without magnet Single acting u i r y o e w i e u !0 Built-in magnet Without magnet Rod end male thread Parts list Replacement parts: Seal kits (double acting) Contents Note No. Description Material Kit no. Bore size 1 Hard anodized Aluminum alloy 4 CUJB4-PS Cylinder tube 2 Above numbers 11, 12, 13 and an exclusive grease pack.

Compact Type

9 from the chart above CXSM32-PS CXSL15APS CXSL20APS CXSL25APS CXSL32APS 8 Series CXSJ Construction: Axial Piping CXSJ6P, CXSJ10P e q t w r u y i o Parts List: Axial Piping No.

AME

AFF AMl Related poroducts Mounting Caution q Verify the direction of the flow of the compressed air and the e mark that indicates the inlet of the product before connecting.

Micro Mist Separator with Prefilter AMH Model Model AMH250 AMH350 AMH450 AMH550 AMH650 AMH850 AMH150 Series AMH can separate and (1) remove aerosol state oil mist in 500 1000 2000 3500 6000 12000 200 Rated flow (l/min(ANR)) compressed air and remove Po

AMH850 is aluminum casting. w e Sight glass Tempered glass Replacement Parts AMH450 Part No. No.