EXxx-OMQ0015CN Content 0 10 1 11 2 12 3 13 4 14 5 15 6 16 7 17 Unit diagnostic status 1 7 6 5 4 3 2 1 0 Byte 3 Bit No.
No.EX-OMV0023-A PRODUCT NAME SI unit for Ethernet POWERLINK MODEL / Series / Product Number EX260 Series Table of Contents Safety Instructions 2 Model Indication and How to Order 8 Summary of Product elements 9 Installation and Wiring 10 Installation 10 Wiring 11 LED Indication and Settings 15 Configuration 17 Troubleshooting and Maintenance 21 Specifications 26 Specifications 26 Dimensions
Do not continue idling except for priming the pump. 5 11. Condensation and freezing of the pilot port The location around the switching valve and the air exhaust port can cool down quickly due to expansion of the supply air, and this may cause condensation on the piping and the condensation may freeze during operation in winter.
Do not continue idling except for priming the pump. 5 11. Condensation and freezing of the pilot port The air supply port of the air operated type can cool down quickly due to expansion of the supply air, and this may cause condensation on the piping and the condensation may freeze during operation in winter.
How to Order 11 2-2-1. MONOSASHI-KUN with BRAKE 11 2-2-2. Options 12 Chapter 3: Selection Flow Chart to Confirm Utility 1314 Chapter 4: Specifications 4-1. Cylinder Specifications 15 4-2. Sensor Specifications 15 4-3. Cylinder (Brake) Life 16 Chapter 5: Wiring 5-1. Connector Wiring Table 17 5-2. Wiring for Counter (Controller) 17 5-3. Wiring for Extension Cable 18 5-4.
Operation failure Incorrect wiring (1) Fuse blown out and/or lead wire broken (2) Incorrect contact at the contact and connection (3) Broken wire in the coil (4) Foreign matter caught in the spool valve (8) Swollen spool valve (5) Excessive oil supply (11) Coil has burned out.
Wire the communication line away from the noise source. 11 NS: Green LED is flashing Communication is not established. Check the following, and restart. Signal line is connected from PLC. The communication speed of PLC and SI unit is appropriate. Wire the communication line away from the noise source. NS: Red LED is flashing Communication timeout.
SF: OFF BF: Red LED is ON 11 SF: Red LED is ON BF: Red LED is ON Address setting is defective. If the SI unit address is set to 0 or 126 or more, set it to between 1 and 125. SF: Red LED is ON BF: Red LED is flashing Configuration does not match. Check the configuration setting of PLC, and ensure it matches the actual configuration.
Description and Functions 9 5-1 LED indication 9 5-2 Terminal board 9 5-3 Address setting 10 5-4 Setting of Hold/Clear 11 6. Wiring 12 6-1 Communication wiring 12 6-2 Terminal resistance 13 6-3 Cable for communication line 13 6-4 Wiring to power supply 13 7. Troubleshooting 14 -1No.EX-OMF0012-B 1.
How to Use . 11 2-1. Procedures to operation . 11 3. Wiring . 12 3-1. AC adapter type/ IZG10-01, 02 . 12 3-2. Power supply cable type/ IZG10-03 . 12 4. Function . 13 4-1. Name of parts . 13 4-2. LED indication . 13 4-3. Mode setting switch . 14 4-4. Emitter maintenance (cleaning and replacement) . 15 4-5. Alarm function . 17 5. Performance . 18 5-1.
Exhaust Port Exhaust Residual pressure exhaust button (2.9) Port -4- Warning Warning Design/ Selection Design/ Selection (11) Push the residual pressure exhaust button all the way to the end position by using a tool. Push the residual pressure exhaust button all the way to the end position by using a tool having a tip diameter of 2.8 or below.
Recommended tightening torque: Modular AR/AW series 0.60.05 Nm ARM10/11 series 0.320.03 Nm Mount the main body of the Pressure switch. Insert the lock pin to the adapter to the end firmly. Supply pressure slowly, and ensure no air leaks.
Air Cylinder Speed controller Solenoid valve Regulator Air source Air filter Fig. 11 Basic Circuit 28 6.