Please contact us for the latest version.sales@ocaire.com, VALVE, SOL, BODY PT, VALVE, SYJ500 SOLENOID VALVE 3/PORT, BA, SYJ500 BODY PORT M5, .11343 lb
AC Servo Motor Driver (Pulse input type/Positioning type) Chapter DC Direct Current EMI Electro Magnetic Interference EPDM Ethylene Propylene Diene Monomer ERR Error IEC International Electrotechnical Commission LCD Liquid Crystal Display PE (Electricity) Protective Earth PE (Material) Polyethylene PID Proportional, Integral, Differentiate PPS Polyphenylene Sulfide PV Process Value RET Return RXD Received Data SEL Select SER (No.) Serial (No.)
Rubber grommet Signal cable entry L N PE Strain relief Power supply cable entry IDFC60/70/80/90 Series 2.1Name and Function of Parts 2-1 IDX-OM-U010 Chapter 2 Name and Function of Parts Left ventilation grille (air intake opening) (Dustproof filter) Air intake for cooling.
Rubber grommet Signal cable entry Strain relief Power supply cable entry L N PE (to be connected to the user's equipment) Refer to 3-5 for details for electric wiring. IDFA60/70/80/90 Series 2.1Name and Function of Parts 2-1 IDX-OM-V020 Chapter 2 Name and Function of Parts Left ventilation grille (air intake opening) (Dustproof filter) Air intake for cooling.
-T: 1300/1500 Temperature stability Note 4) C 2 Circulating fluid system Pump capacity (50/60 Hz) Note 5) MPa 0.08 (at 7 L/min)/0.11 (at 7 L/min) For option -T: 0.13 (at 7 L/min)/0.18 (at 7 L/min) Rated flow (50/60 Hz) Note 6) L/min 7/7 Tank capacity L Approx. 5 Port size Rc1/2 Fluid contact material Stainless steel, Copper (Heat exchanger brazing), Bronze, Brass, Ceramic, Carbon, PP , PE
Stainless (I include heat exchanger brazing), Aluminum oxide ceramic, SiC, Carbon, PP, PE, POM, FKM, EPDM, PVC (No. copper used) Circulating fluid wetted materials Servieable conductivity: 0.22S/cm or more. (Resistivity: 4.5Mcm or less.) This option doesnt include a function to maintain high resistivity/conductivity. You need ion exchange resin filter (DI filter) for the purpose.
Reference data Units: mm IDH6 Jumper cord 7 6 5 4 3 1 PE Remote start/stop Fault-signal (N.O: Close at "Fault") Fault-signal (N.C: Open at "Fault") 1042 31 N 2 L Operation-signal (N.O) Ground Terminal screw: M3 Suitable wire: 1.25mm or more 2 244 Power supply Connector width: 6.5mm or less Detail of wiring 35 184 172 392 (Note) 15 80 223 321 3001 485 The type without built-in filter does
X, PE port PCW type There is no need to enter anything when the SUP/EXH block mounting position M is selected. Pilot spec.
Out connector with spanner during piping. 5 Wait 3 minutes before restart. 6 Ensure Running Condition / Evaporating Temp. in green zone. 1 2 3 4 5 6 i 5 IDH Series i.2 IDX-OM-W038 i i.3 HFC i 6 IDH Series i.3 IDX-OM-W038 i i.4 1 1.5 () i.4 i 7 IDH Series IDX-OM-W038 1. 1 1.1. 1-3 10mm 17mm (22mm) 17mm (22mm) IDH Series 11 1.1 IDX-OM-W038 1. () OFF ON () 3 7 6 5 1 2 4 PE
As the PE port is the exhaust port of the pilot valve, do not plug or restrict it. 2. The X port is the pressure supply port of the pilot valve and PE port is the exhaust port of the pilot valve. Pay attention that these ports should be connected correctly. 7 VG300**-OMH0006-A Trouble shooting Perform troubleshooting with higher possibility based on the failure phenomenon.
, (H): SYJ7220-01 Built-in one-touch fitting: SYJ7220G: Approx. 300 H: Approx. 600 (Lead wire length) 107.4 [111.8] 63 3 13 B A B A Manual override 17 35 17 2-3.2 (For manifold mounting) 1/8 (A, B port) One-touch fitting (A, B port) (4.9) 2-3.2 (For mounting) (Light/surge voltage suppressor) Applicable tubing O.D.: 6, 1/4" : 8, 5/16" 35 36 + 28 25 16.1 31.5 [38.5] 21 1.6 P R2 R1 18 1.6 (PE
(included) M3 x 6l Binding band (included) 34 Holding plate (included) 4-M6 x 1 C section 30 D When using a PE terminal, use accessories included as shown above.
The built-in circulator tank is made of resin (PE). Therefore, the tank may be crushed if the pressure is negative. Special attention must be paid if the flow rate of the circulating fluid is high. To avoid a negative pressure of 0.02 MPa or below, the piping return should be as thick and short as possible to minimize piping resistance.
Hz L/min 55/68 Maximum pump head m 50 Minimum operating flow rate 50/60 Hz7 L/min 29/45 Tank capacity L 18 Circulating fluid outlet, circulating fluid return port Rc1 (Symbol F: G1, Symbol N: NPT1) Tank drain port Rc1/4 (Symbol F: G1/4, Symbol N: NPT1/4) Pump capacity Fluid contact material Stainless steel, Copper (Heat exchanger brazing), Brass, Bronze, PTFE, FKM, EPDM, PVC, NBR, POM, PE
PE!$cI;i~tj9h ",' Action Double aCllng single rod Double acti ng single rod 'Model i Standard type CS2 iCS~ ,: Smooth cylinder CS2Y How to Order 0 .. c o C I A With rod end bracke t D o a. ..
Be sure to leave it open as if the PE port is blocked, normal pressure setting cannot be performed.
Note 1) Air consumption is approx. 9.5 L/min (ANR) [at a supply pressure of 1.0 MPa].
Note 2) If there is an abnormal amount of air leakage from the PE port, the diaphragm may be damaged.
Please contact us for the latest version.sales@ocaire.com, VALVE, DBL SOL, BODY PT (DC), VALVE, SY3000 SOL/VALVE, RUBBER SEAL, BE, SY BODY PORT (M5, NON-US STD), .17240 lb
Please contact us for the latest version.sales@ocaire.com, VALVE, DBL SOL, BODY PT (DC), VALVE, SY3000 SOL/VALVE, RUBBER SEAL, BF, SY BODY PORT (M5, NON-US STD), .17636 lb