.: 03 (R3/8, Rc3/8), Thread Material/Surface Treatment: N (Brass + Electroless Nickel Plate), Sealant: P (Face Seal)
.: 03 (R3/8), Thread Material/Surface Treatment: A (Brass), Sealant: P (Face Seal)
.: 03 (R3/8), Thread Material/Surface Treatment: A (Brass), Sealant: P (Face Seal)
.: 03 (R3/8), Thread Material/Surface Treatment: A (Brass), Sealant: P (Face Seal)
.: 03 (R3/8), Thread Material/Surface Treatment: A (Brass), Sealant: P (Face Seal)
.: 03 (R3/8), Thread Material/Surface Treatment: N (Brass + Electroless Nickel Plated), Sealant: P (Face Seal)
.: 03 (R3/8), Thread Material/Surface Treatment: A (Brass), Sealant: P (Face Seal)
.: 03 (R3/8), Thread Material/Surface Treatment: A (Brass), Sealant: P (Face Seal)
.: 03 (R3/8), Thread Material/Surface Treatment: N (Brass + Electroless Nickel Plated), Sealant: P (Face Seal)
.: 03 (R3/8), Thread Material/Surface Treatment: A (Brass), Sealant: P (Face Seal)
.: 03 (R3/8), Thread Material/Surface Treatment: A (Brass), Sealant: P (Face Seal)
.: 03 (R3/8), Thread Material/Surface Treatment: A (Brass), Sealant: P (Face Seal)
.: 03 (R3/8), Thread Material/Surface Treatment: A (Brass), Sealant: P (Face Seal)
.: 03 (R3/8), Thread Material/Surface Treatment: A (Brass), Sealant: P (Face Seal)
.: 03 (R3/8), Thread Material/Surface Treatment: A (Brass), Sealant: P (Face Seal)
CC-Link-E RW w 1 U nused RW r1 U nused RW w 2 U nused RW r2 U nused RW w 3 U nused RW r3 U nused O ut put dat a occupi es 4 w ords, but uses onl y t he 1st w ord act ual l y. The pressure i s set by b15, b1, b0 dat a. ( b11 b0 cover 100% F. S. ) The l i m i t i s 1198h, dat a of 110% , but t he guarant eed accuracy i s up t o 100% F. S.
NPT, R1/4 8 to 12 NPT, R3/8 15 to 20 NPT, R1/2 20 to 25 or loosen the threads. (3) Reuse Normally, fittings with a sealant can be reused 2 to 3 times. Caution (4) Once the fitting has been tightened, backing (1) Be certain to wear safety glasses at all times it out to its original position often causes the sealant to become defective.
R3/8, NPT3/8, G3/8 22 7/8 R1/2, NPT1/2, G1/2 27 1-1/16 (4)For M5, 10-32UNF Tightening method First, tighten it by hand, then give it an additional 1/6 turn to 1/4 turn with a wrench. Refer to the table below for reference values.
Not recommended Not recommended Connection thread size Tightening torque [Nm] b) If the fitting is tightened with excessive torque, R1/4 812 R3/8 1520 a large amount of sealant will seep out. Remove the excess sealant. c) Insufficient tightening may cause seal failure, or loosen the threads. d) Reuse 1. Normally, fittings with a sealant can be reused 2 to 3 times. 2.
Warning Male thread Tightening torque [Nm] R3/8 22 to 24 1. Install a stop valve on the supply pressure side of the blow gun. 5. Allow extra length when connecting a tube to accommodate changes in tube length due to pressure. It will be emergency shut off in case of unexpected leakage or damage. 6.