PFMC.eng Verify the specifications before use. [ Un i] Unit selection function 1 [ L] L/min Default settings When the flow exceeds the set value [P_1], the switch will be turned ON. When the flow falls below the set value by the amount of hysteresis [H_1] or more, the switch will turn OFF. If the operation shown in the diagram below is acceptable, then keep these settings.
[F95] [LPm] L/min [Un i] Unit selection function [F99] [ in i ] Reset to the default settings [oFF] Unused Maintenance Connecting / Disconnecting When mounting the connector, insert it straight into the socket, holding the lever and connector body, and push the connector until the lever hooks into the housing, and locks.
Hysteresis mode I Instantaneous flow The flow passing per unit of time. If it is 10 L/min, there is a flow of 10 L passing through the device in 1 minute. Insulation resistance Insulation resistance of the product. The resistance between the electrical circuit and the case. The voltage drop across the product (and therefore not applied to the load), when the switch output is ON.
I Instantaneous flow The flow passing per unit of time. If it is 10 L/min, there is a flow of 10 L passing through the device in 1 minute. Internal voltage drop Voltage reduction across an internal device when the switch output is in the ON condition. O Operating fluid temperature Range of fluid temperature that can be used by the product.
O Cable Length for LEC: Without Cable, Controller Mounting: 8 (DIN Rail Mounting), Communication Plug Connector or I/O Cable Length for JXC: 1 (1.5m)
Product Warranty HRR Series 10-2 Revision Revision I : [May.2022] Note: Specifications are subject to change without prior notice and any obligation on the part of the manufacturer. 2022 SMC Corporation All Rights Reserved
History History Version Preface Contents Chap.1 Chap.2 Chap.3 Chap.4 1.0 Jul/7/22 Jul/7/22 Jul/7/22 Jul/7/22 Jul/7/22 Jul/7/22 Record of Changes Version Contents Date 1.0 First edition Jul/7/22 HEF002-A6 i Preface Preface Thank you very much for purchasing SMC Thermo-con. This manual contains description for communication protocol of this product for your full benefit from this product.
History History Version Preface Contents Chap.1 Chap.2 Chap.3 Chap.4 1.0 Feb/19/21 Feb/19/21 Feb/19/21 Feb/19/21 Feb/19/21 Feb/19/21 Record of Changes Version Contents Date 1.0 First edition Feb/19/21 INR-244-831 i Preface Preface Thank you very much for purchasing SMC Thermo-con.
Table 1 Moment of inertia Size Allowable kinetic energy (J) 10 0.00015 15 0.00025 20 0.0004 30 0.015 40 0.03 How to calculate the load energy E : Kinetic energy (J) I : Moment of inertia (kg m Speed (rad/s) : Rotation angle (rad) 1803.14 rad t : Rotation time (s) 1 E = I 2 2 2 = t Table 2 Safety operable rotation time adjustment range Size Rotation time ( s / 90) 10 0.03 to 0.5 15
The vacuum aspiration fluence shows the fluence immediately before piping in the actuator. 6 - How to Order Step motor (servo 24VDC) / Servo motor (24VDC) 11-LEFS 25 B 6N 1 100 1 ize Controller mounting Screw mounting type Screw mounting type Nil Nil 16 16 DIN rail mounting type DIN rail mounting type D D 25 25 I/O cable length 32 32 40 40 Without cable Without cable Nil Nil Motor 1.5m
LED (P.28) LECLEDALM CC-Link CN4 I/O 16. (P.71) * 7 4.2 (P.18) PLC CC-link LED LED PWR ALM L ERR CC-Link L RUN CC-Link LED 8. LED (P.28) (LEC)LEDL RUNLEDL ERR/PLC PLC 17. CC-Link (P.77) 4.2 (P.18)4.3 PLC (P.18)PLC 10 - 8() ()() () 9 10. (P.32) PLC 14.
10218: Manipulating industrial robots -Safety JIS B 8370: JIS B 8361: JIS B 9960-1: (1 ) JIS B 8433: *2) 1. 2. 3. 1. 2. 3. 4. 4 - LEC-G Series/ / 1 1.5 5 - 2. 2.1 (GW)LEC (LECP6,LECA6)EtherNet/IP 1 12 LEC * 2.2 DIN D DIN EN1 EtherNet/IP G GW 6 - 2.3 PLC LEC-T1-3G HUB EtherNet/IP GW LEC-W2 LEC-GEN1 LEC RS485Modbus LEC-CGR LEC (LECP6, LECA6) LE Series Modbus GW LEC LEC I/
Parallel I/O Type: P (PNP), I/O Cable Length: 5 m, Option: D (DIN Rail Mounting)
O Cable Length for LEC: Without Cable, Controller Mounting: 8 (DIN Rail Mounting), Communication Plug Connector or I/O Cable Length for JXC: 1 (1.5m)
Available protocols include DeviceNet, CC-Link, AS-i, Profibus-DP, and CANopen.
1 @0 @1 w o e i !5 MHZ MHF r !7 !6 t !8 !0 !2 i !9 y u MHL Component Parts MHR MHR Description Material Description Material Note No. Note No.
Stainless steel specifications (Stainless steel 303) KG Series AS-FG Series Resin connector 90-I(Z)SE Series Front matter 5 92-MSQB Series Material restriction + Vacuum port for vacuum suction Using a vacuum port for vacuum suction enables reducing more dust particles than 90series.
1 r e w q y i Cover 2 Aluminum alloy AMD Fitting body 3 PBT Cassette 4 PP, EPDM, Stainless steel AMH Bracket 5 Stainless steel alloy O-ring A 6 H-NBR AME O-ring B 7 H-NBR Rod cover 8 Stainless steel alloy AMF Tie-rod 9 Stainless steel alloy Cap nut 10 Stainless steel alloy ZFC Plain washer 11 Stainless steel alloy t u !0 Replacement Parts SF No.
Dimensions EVS1-02-FG-S-M0 102 68 21.5 (14 port) 21.5 (12 port) 8.5 (2 port) 8.5 (4 port) 14 4 2 12 12 34 25 18 14 5 1 3 Indicator light 29.5 32.5 34 2-4.6 mounting holes 37 Manual override M8 connector 15.5 (12-, 14 port) 9 (2-, 4 port) 74.5 66.5 8.5 PE port 23 13.5 SMC 16 16 M5-2 ports 12, 14 port 1/8-2 ports 2, 4 port 1/8 1 port 1/8-2 ports 3, 5 port EVS1-02-FG-D-M0 EVS1-02-F G-D-M0 H J I
End bracket Accessories (options) Nil I Y In case of built-in magnets without auto switches, the auto switch type symbol is "Nil".