Series AK1000 Rotate the handle by hand. 1. Conrm the mounting direction of the product. Direction of gas flow from inlet to outlet is indicated by an arrow on each label. Orient the valve as specied by the system designer. 2. Connect actuation pressure to the valve actuator connection. (Air operated type) Use nitrogen or clean dry air for actuation pressure. The connection M5 thread.
To prevent lurching of the nozzle due to air pressure, confirm that the nozzle is not loosened or rattling by pulling on it by hand before operation. 7. Do not use the product to clean or remove toxic substances or chemicals. 8. Do not drop, step on or hit the product. This may cause damage. 9.
Assemble by following the assembly procedure on page 13. For D-M9 1. Assemble by following steps 1 to 5 of the above procedure. 2. Carefully fix the switch holder (25) to the holding block (17) using the cross recessed round head screw (26). 3.
As an equipment, calibration should be done by customer.
100 101 to 125 126 to 150 16 to 30 31 to 45 46 to 60 61 to 75 76 to 100 101 to 125 126 to 150 5 to 15 Bore 10 16 53.5 61 73 85 81 93 105 73.5 53.5 62 74 86 92 116 134 146 82 94 106 112 136 154 166 73.5 Dimensions by stroke/Spring extend (Dimensions not mentioned in the below table are the same as the above table.)
Never carry a cylinder by its lead wires. This may not only cause broken lead wires, but it may cause internal elements of the switch to be damaged by the stress. 3. Mount switches using the proper tightening torque. When a switch is tightened beyond the range of tightening torque, the mounting screws, mounting bracket or switch may be damaged.
Compact and light Less space is required for mounting than the NCJl series the cover width has been redused by 10o/o. The weight has also been reduced by 30% with the new design.
The assembly, operation and maintenance of machines or equipment including our products must be performed by an operator who is appropriately trained and experienced. 3.
The weight has also been reduced by 30% with the new design.
Finger motion is synchronized by a rack and pinion mechanism.
Watchmakers (precision) screwdriver CY1F CYP Mounting screw M2.5 x 0.45 x 4 L Lightweight Switch mounting bracket The body weight has been reduced by approximately 10% by eliminating unnecessary body weight and by reducing the outer diameter of the cylinder tube.
Speed Controller Adjustable by Flat Head Screwdriver with One-touch Fitting Elbow Type/Universal Type AS1F-D Series RoHS Flow adjustable by flat head screwdriver Model Prevention of an unnecessary manual operation Flat head screwdriver Applicable tubing O.D.
In this region, as a rule, operate the cylinder by providing a guide along the direction of movement. The below table shows the applicable maximum stroke (in cm units), found by calculation assuming the case where the force generated by the cylinder itself acts as buckling force on the piston rod, or piston rod and cylinder tube.
Do not carry a cylinder by the auto switch lead wires. Never carry a cylinder by its lead wires. This may not only cause broken lead wires, but it may cause internal elements of the switch to be damaged by the stress. 3. Mount switches using the proper tightening torque. When a switch is tightened beyond the range of fastening torque, the mounting screws or switch may be damaged.
32 x 2)1 40% 6.6 Increased by Improved by up to times Allowable lateral load Non-rotating accuracy 0.06 0.4 kg 0.1 0.06 kg CXSM10 50 mm stroke (10 x 2)1 JMGPM12 50 mm stroke (10 x 2)1 CXSM32 25 mm stroke (32 x 2)1 JMGPM40 25 mm stroke (32 x 2)1 + m 1 Both cylinders used in the comparison have almost the same piston area.
Transportation/installation shall be performed by multiple operators. Never mount a product in a location that will be used as a foothold. The product may be damaged if excessive force is applied by stepping or climbing onto it. Wiring Avoid repeatedly bending or stretching the cables, or placing heavy load on them.
Do not scratch or gouge the linear guide by striking it with other objects. 3. Since the slide table is supported by precision bearings, do not apply strong impacts or excessive moment when mounting work pieces. 4. The cylinder can be operated by directly applying a load within the allowable range.
Polishing of wafers Lateral load resistance Lateral load resistance is increased by a built-in ball bushing.
Continuous suction and discharge is performed by the reciprocal motion of the diaphragm. 2.
Continuous suction and discharge is performed by the reciprocal motion of the diaphragm. 2.