CE2 Relay, PLC 24 V Yes Grommet 3-wire (NPN) IC circuit Diagnostic indication (2-color) 5 V, 12 V 3-wire (PNP) 12 V 2-wire A96V A96 IC circuit 5 V 3-wire (NPN equiv.)
Refer to Best Pneumatics vol.8 (CY1 series model selection method) for details. 12-REA40 12-REA40 6 2.1 12-REA50 12-REA50 8 3.4 12-REA63 12-REA63 8 3.4 3. Throttle type speed controllers are recommended for speed adjustment, as shown in the table below. Recommended speed controller Model 5. Do not scratch or gouge the external surface of the cylinder.
Transporting using casters 1) This product is heavy and should be moved by at least two persons. 2) Do not grip the piping port on the right side or the handles of the panel. 3) When transporting using a forklift, be sure not to let it hit the casters or adjusters, and drive the fork all the way through until it comes out the other side. 4) Do not get across steps with casters. 2.
through until it comes out the other side. 4) Do not get across steps with casters.
Caution SMC Pressure Switch and Pressure Sensor do not have explosion-proof construction; do not use flammable gases or liquids. Also, do not use toxic gases or liquids. 888
Hold/Release success: default output DO[101] Hold/Release failure: default output DO[102] * Digital output port can be selected within DO[101] to DO[112] * you select the same digital output port for different status signals, a warning message will be displayed. 2. Test run The manual operation of the magnet gripper unit can be checked.
Do not use non-defined or unavailable addresses or flags. Otherwise, the Card Motor may make an unexpected movement, leading to damage.
Do not use a cable longer than 100 m. For long wire lengths, we recommend a ferrite core should be attached to both ends of the cable, to reduce noise. (2) Do not use a load which generates a surge voltage.
Do not torque it more than required in case to operate a lock type manual.
M5 11.5 1/8 34 (8) Do not use this product in such a way that Body A rotates at any time. Also, do not use it in such a way that moment loads act on it. Body A or the joint may be damaged.
Caution As a jig is required for bore size 6, do not disassemble when replacing seals etc. If overhaul is required, contact SMC Sales Office.
Recommended tightening torque [N-m] Piping Warnin Warnin Warnin Warning g g g Thread 1/4 Torque 12 to 14 Do not apply any additional twisting, or bending moments except for the weight of the filter regulator itself. Provide separate support for external piping, as damage may otherwise occur.
Recommended tightening torque [N-m] Thread 1/4 Piping Warning Torque 12 to 14 Do not apply any additional twisting, or bending moments except for the weight of the filter regulator itself. Provide separate support for external piping, as damage may otherwise occur.
Do not make any modifications to be product. Do not take the product apart. Piping Caution 1. Before piping Make sure that all debris, cutting oil, dust, etc, are removed from the piping. 2. Wrapping of pipe tape When screwing piping or fittings into ports, ensure that chips from the pipe threads or sealing material do not get inside the piping.
3.2 AFF,AM,AMD 90D 148 93.5 58.5 110 22 11 20 12 3.2 -22- Doc. no.
However, do not use the product under water.
Precautions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
Please contact SMC if it is necessary to hold a stopped position for an extended period of time. 11.Do not disassemble the product or make any modifications, including additional machining. Doing so may cause human injury and/or an accident. 12.Resumption after a long period of holding time 4.
Do not apply excessive force or shock to the body or fittings with an impact tool. It can cause damage or air leakage. 100 8 7 to 9 150 1/8 14 12 to 14 200 1/4 17 22 to 24 200 3/8 21 28 to 30 200 1/2 24 Lock Nut Tightening Torque Caution 1. Suitable screw torque for a hexagon lock nut is shown in the table below.