IDX-OM-X011 Do not connect the earth to a water pipe, a gas pipe, or a lightening rod. Do not plug too many leads into a single socket. That causes exothermic heat or fire. Do not modify the internal electrical wiring of the product. 10.2 Specifications An earth leakage breaker is installed in the product.
Caution Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Warning Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Danger Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury. Warning 1.
Do not use a sealant material other than pipe tape. 6. In cases where positioning is required, turning the fitting in the reverse direction after tightening will cause air leakage. Back page 6 Series KK130 Specific Product Precautions 5 Be sure to read before handling.
When tightening the mounting screw, use a watchmakers screw driver with a handle 5 to 6 mm in diameter. Tighten with a torque of 0.10 to 0.20 Nm.
When used in a potentially explosive atmosphere F requiring the use of category 1G equipment, the apparatus must be installed so that, in the event of rare incidents, an ignition source due to impact or friction is excluded. 6. Do not use it in a non-hazardous area where air leakage would cause a risk. 7.
9i @2 q r y#0 $0 $2 w $3 #8 @9 A C B Section A !2 !2 #4 @6 #9 @8 $4 #2 #1 #6 #7 $6 !0 u @5 !6 @1 !1 $7 o $8 e $1 !2 Section B Section C 100 80 63 50 40 32 80, 100 80, 100 Description Material Note Parts list Description Material Note Parts list No. No.
D-M9WV 6 6 7 7.5 D-A9, D-A9V 9.5 9.5 9.5 11.5 Since this is a guideline including hysteresis, not meant to be guaranteed.
A B 3 5.5 7 7 15 60 65 + 45 (n-2) D-H7, D-H7W D-H7F 30.5 28.5 30 30 n-2 2 15 + 50 ( ) (n = 2, 4, 6...) Approx. Hs 30.5 35 40.5 47.5 D-H7C 15 65 10 65 + 50 (n-2) A B Approx. Hs 3 5.5 7 7 n-2 2 D-H7C 31.5 28.5 30 30 15 + 50 ( ) (n = 2, 4, 6...)
1 u @5r @6 @6 !5 !5 @1 q @9 @7 @4 e #2 #0 i @2!9wy!6@3 A B CLJ2 CLM2 A CLG1 CL1 B Extension locking Without magnet !0o#1 @8 t MLGC Section A-A' CNG MNB !3 @0 CNA CNS Section B-B' (Both ends tapped) CLS Retraction locking CLQ Section B-B' (Through-hole) !4 !7 !8 #3 RLQ MLU MLGP ML1C With bumper Rod end male thread Note) The sectional drawing above shows the locked condition.
D-B5/B64 D-G5/K59 D-G5W/K59W (A set of band and screw) BA-02 BA-01 (A set of band and screw) BA-32 (A set of band and screw) BA-04 (A set of band and screw) BA-05 (A set of band and screw) BA-06 (A set of band and screw) BA-08 (A set of band and screw) BA-10 (A set of band and screw) Note) Since the switch bracket (made from nylon) are affected in an environment where alcohol, chloroform,
-*04-*DZM 1/2 98 133 47 61 34 52 64 (Max. 73) AVL5000-*06 to 10 3/4 & 1 128 161 59 77 74 64 (Max. 73) AVL5000-*06 to 10-*DZM 3/4 & 1 128 161 59 77 34 74 64 (Max. 73) Soft start valve with lock out H Air direction Nil Left to Right C E D F Port thread Rc Body size R Right to Left Nil 20 1/4 N NPT 30 3/8 F G 40 1/2 50 3/4, 1 Electric entry 1(P) 2(A) Port size Manual lockout Nil 1/4 (AVL2000
P: With plug (M-5P) For non-plug-in only Rated voltage 5 6 24 VDC 12 VDC When mounting a pressure sensor etc., select Nil.
This acceleration process can be achieved smoothly (as a SIN function) by using a cushion spear on which a Ushaped groove is machined. 6. Reset 3. Acceleration Actuating air passes from cylinder port on rod side and enters the left chamber of the cylinder from space between cushion seal and U-shaped groove on the outer surface of cushion spear.
CM PE FM1 PRS P FM2 PE CM FM 12 OLR PTC PTC ILS PRS TB PE GFCI EDV 6 3 6 6 4 2 6 4 7 A A 7 1 7 2 A m 3/h(ANR) 1) (50/60Hz) 0.32/0.375 10 1ANR 65% 2 7 3 7 1 8 C 8 C 8-1 8-2 1) 2) 8-3 8 1 9 G G 9-1 9 1 10 H 10 H 10-1 ( ) 10-2 () AD48-2-A 10 IDFA6E-20-H N.O. () 0.151.0MPa 10 1 10 H IDF-S1941 () 1 AD48-2-A 1 1) 2019 3 2019 2 SERIAL No.XP IDF-S1940
If the driving direction is unclear, operate the actuator slowly with a small move distance while checking the driving direction. -27- 6.
This produces an air cushion cylinder which retains the merits of a compact design. Working principle A + A' A' A A' A' R H R H Piston seal When the piston is retracting, exhaust is discharged from both A and A' until piston seal H passes the air passage A. After piston seal H has passed the air passage A, exhaust is discharged only from A'.
4.5 (7) 4.5 (7) 5 (10) 6.5 (11.5) 7 (12) A 10 (12.5) 10 (12.5) 10.5 (15.5) 12 (17) 12.5 (17.5) Hs A 5 (7.5) 5 (7.5) 5.5 (10.5) 7 (12) 7.5 (12.5) A 5 (7.5) 5 (7.5) 0 (4) 1 (6) 1.5 (6.5) A 2 (4.5) 2 (4.5) 2.5 (7.5) 4 (9) 4.5 (9.5) A Hs Hs Hs Hs Hs Hs CU 25 32 33 39 35.5 37.5 34.5 CQS 32 39 40 46 42.5 44.5 41.5 CQM 0.5 (5.5) 2 (7) 2.5 (7.5) 40 56.5 47 48 54 50.5 52.5 49.5 CQ2 50 66 56 57
4.5 (7) 4.5 (7) 5 (10) 6.5 (11.5) 7 (12) A 10 (12.5) 10 (12.5) 10.5 (15.5) 12 (17) 12.5 (17.5) Hs A 5 (7.5) 5 (7.5) 5.5 (10.5) 7 (12) 7.5 (12.5) A 5 (7.5) 5 (7.5) 0 (4) 1 (6) 1.5 (6.5) A 2 (4.5) 2 (4.5) 2.5 (7.5) 4 (9) 4.5 (9.5) A Hs Hs Hs Hs Hs Hs CU 25 32 33 39 35.5 37.5 34.5 CQS 32 39 40 46 42.5 44.5 41.5 CQM 0.5 (5.5) 2 (7) 2.5 (7.5) 40 56.5 47 48 54 50.5 52.5 49.5 CQ2 50 Courtesy