SZ3000 1 i q w t y e 5(R) SOL.a SOL.b 3(R) 1(P) SZ3C60K/With back pressure check valve 4(A) 2(B) SOL.b 5(R) SOL.a 3(R) 1(P) o 5 (R) 1 (P) 3 (R) Component Parts SZ3A60K/With back pressure check valve Material Note For N.C. (Normally closed) Description No. q w e r t y u i o Resin/HNBR Spool valve assembly e r t !0 !1 i q q u y For N.O.
3 (R2) 1 (P) 5 (R1) 3 (R2) 1 (P) 5 (R1) e w q r e w q r 2 position double 2 position double (A) 4 (B) 2 (A) 4 (B) 2 3 (R2) 1 (P) 5 (R1) 3 (R2) 1 (P) 5 (R1) e w q e w q r r Note) 3 position pressure center 3 position exhaust center 3 position closed center 3 position pressure center 3 position exhaust center 3 position closed center (A) 4 (B) 2 (A) 4 (B) 2 (A) 4 (B) 2 (A) 4 (B) 2 (A) 4 (B
Applicable manifold base Plug-in type With attachment plug lead wire: Type 51G Description Component parts Manifold block u, Junction box i, Lead wire assembly o Tie-rod y, O-ring e, r, Seal A q VVZS2000-1A-1-Port size (1) Manifold block assembly Manifold block u, Tie-rod y, O ring e, r, Seal A q Non plug-in type: Type 51 VVZS2000-1A-2-Port size (1) Plug-in type With D-sub connector: Type
dimensions MLGPL (ball bushing)/A, DB, E dimensions A E A E Bore size (mm) Bore size (mm) DB st50 50
L/min w e L t Unit display of flow rate for air/ Red (PF2A200, 201 for air only) CH1 to 4 will illuminate when the normal condition (nor) is selected. e OUT1 CH y Unit display/Orange Illuminates the selected unit.
) x PC F=-q x PA+r x PB+(w-e) x PC F=q x PA q, w and e are piston areas.
Select (d) [Pairing mode] from (c) [Remote registration] on the (a) [Properties] tab and then click (e) [Reset module]. Base setting screen (e) (b) (a) (c) (d) A Base unit that supports CC-Link (EXW1-BMJA#) will change to pairing mode using the protocol set in "System setting".
C D A B Side support B MY-SB 2 x J MY1B MY1B MY1H E A B MY1B C D MY1M (mm) MY1C A 61 70 87 B C D E F G H J Part no.
(Port indication: P: supply port; V: vacuum port; E: exhaust port.) Matching the ejector to the vacuum circuit Refer to technical data on page 13-110 to 19 for precautions on the vacuum circuit.
F = degrees Fahrenheit S = SeCOndS NUmin = Normal liters per mlnute World Wide QS\E Support...
I J E Z (R2)(PxFl) (R2XPXR1) Prssure Center NVF3530 (B) (A) Spej;ifications -, Flurd-Art f Operatangprssurcrange2Positionsingle2O-12gPSlS(1.5-9kgF) U 2 pooition double-1 5 1 28 PSI (1 9kgf/cm'?
Series CM2 stainless steel cylinders are compact, lightweight and offer high performance. Improved piston seal and rod seal greatly improve the units life. Rubber bumpers are standard. The CM2 series offers a variety of mounting options and is auto switch capable. Double acting single rod, Bore sizes: 20, 25, 32, and 40 *, Strokes from 25mm through 500mm, Mounts: basic, foot, front and rear
Series CS2 air cylinder is a double acting, non-lube air cylinder. Aluminum die-cast is used for both the rod and head covers, which means a maximum weight reduction of approximately 50% *. This series is available in bore sizes 125mm, 140mm and 160mm with maximum strokes up to 1600mm *. Air cushions are standard on both ends. Other options include auto switches, rod boots, and Rc, NPT or
Series CS1 air cylinder is SMCs largest bore cylinder. This series is available in bore sizes up to 12in. and stroke lengths up to 60in.. Additionally, the CS1 can be ordered auto-switch capable. Other options include, large bore sizes up to 12in. *, various mounting configurations, cushion for noise damping.Double acting, single rod, non-lube type, Bore sizes: 125mm to 300mm, Strokes up
Series CS2 air cylinder is a double acting, non-lube air cylinder. Aluminum die-cast is used for both the rod and head covers, which means a maximum weight reduction of approximately 50% *. This series is available in bore sizes 125mm, 140mm and 160mm with maximum strokes up to 1600mm *. Air cushions are standard on both ends. Other options include auto switches, rod boots, and Rc, NPT or
Series CS1 air cylinder is SMCs largest bore cylinder. This series is available in bore sizes up to 12in. and stroke lengths up to 60in.. Additionally, the CS1 can be ordered auto-switch capable. Other options include, large bore sizes up to 12in. *, various mounting configurations, cushion for noise damping.Double acting, single rod, non-lube type, Bore sizes: 125mm to 300mm, Strokes up
Series CS2 air cylinder is a double acting, non-lube air cylinder. Aluminum die-cast is used for both the rod and head covers, which means a maximum weight reduction of approximately 50% *. This series is available in bore sizes 125mm, 140mm and 160mm with maximum strokes up to 1600mm *. Air cushions are standard on both ends. Other options include auto switches, rod boots, and Rc, NPT or
Series CS2 air cylinder is a double acting, non-lube air cylinder. Aluminum die-cast is used for both the rod and head covers, which means a maximum weight reduction of approximately 50% *. This series is available in bore sizes 125mm, 140mm and 160mm with maximum strokes up to 1600mm *. Air cushions are standard on both ends. Other options include auto switches, rod boots, and Rc, NPT or