AIR COMBINATION Recommended torque unit: Nm Screw 1/8 1/4 3/8 1/2 3/4 1 Torque 3 to 5 8 to 12 15 to 20 20 to 25 28 to 30 36 to 38 *For port size M5: After tightening fitting, tighten approx. 1/6 more by using tool. Do not apply any torsional moment, or bending moment except the weight of the filter regulator itself. External piping needs to be supported separately.
Refer to each construction drawing on the fittings and tubing material. (2) Do not expose the product to direct sunlight for an extended period of time. (3) Do not use in a place subject to heavy vibration and/or shock. (4) Do not mount the product in locations where it is exposed to radiant heat. (5) Do not use the ordinary fittings and tubing in locations where static electricity would
Safety Instructions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
Do not drop or bump. Do not drop, bump or apply excessive impacts (500 m/s2 or more) during handling. The PC wiring system unit can be damaged and connected equipment may malfunction. 2. Be careful of incorrect wiring. Incorrect wiring may result in damage to connected equipment.
Do not use in an atmosphere having corrosive gases, chemicals, sea water, water, water steam, or where there is direct contact with any of these. 2. Do not use in locations influenced by vibrations or impacts. 3. This vacuum regulator always uses atmospheric air, therefore, do not use in dusty environments. 4.
It is already built-in to the rectifier circuit. 50 60 110 VAC Hz [115 VAC Hz] 3 50 60 50 60 50 60 4 220 VAC Hz [230 VAC Hz] Electrical entry D With connector DIN terminal DC specifications of type D and DO is only available with 12 and 24 VDC.
For details, refer to 3 point preset counter/CEU1 on page 10-12-30, and Multi counter/CEU5 on page 10-12-27 respectively.
CAUTION Air combination Do not drop or apply impact during transportation or installation. It will cause damage to the product or operation failure. Do not install in areas of high humidity or high temperature. The product cannot be used in the horizontal or upward directions outside of the specifications.
YES YES Do you want better communication and control capabilities for your system?
Pressure setting mode The pressure can be set by sending input data from the base PLC to the regulator where the full span is 12-Bit. Do not use values outside of the specification range (including Bit 13th to 15th). They are recognized as large values which could cause an error (Er1).
Do not connect wires while the power is on. Otherwise it can break the circuit inside the Auto switch causing malfunction. Do not lay wires or cables with power cable or high-voltage cable in the same wiring route.
Do not release the OUT side piping port of the product to the atmosphere without connecting piping.
Note 9) External scratch marks and dirt are judged as good parts provided that they do not affect product performance.
Do not grip the piping port on the back side or the handles of the panel. 3. Do not pass over bumps, etc., with the casters.
Do not use in an environment where flammable gas or explosive gas exists. Usage may cause a fire or explosion. The products do not have an explosion proof construction. 5. Do not use in a place subject to heavy vibration and/or shock. 6. The valve should not be exposed to prolonged sunlight. Use a protective cover. Note that the valve is not for outdoor use. 7.
Do not use in an atmosphere containing corrosive gases, chemicals, sea water, water, water steam, or where there is direct contact with any of these. Warning Air Supply 2. Do not use in an environment where flammable gas or explosive gas exists. Usage may cause a fire or explosion. The products do not have an explosion proof construction. 1.
Do not use in atmospheres contacting corrosive gases, chemicals, sea water, water, water steam, or where there is direct contact with any of these. 2. Do not use in explosive atmosphere. 3. Do not use in locations subject to vibration or impact. 4. Do not expose to direct sunlight for an extended period of time. Protective cover should be used to shield. 5.
Do not use at location where a negative pressure is applied. The circulating fluid pump should be prepared by the customer. Note 4) The outline dimensions do not included protruding parts such as the foot flange and tube.
Analogue output: 4 to 20 mA Max. load impedance: 300 (12 VDC) 600 (24 VDC) Do not use the product for flammable or highly permeable fluids. A fire or explosion can result. Flow direction OUT side IN side Do not use the product in a place where static electricity is a problem. Otherwise it can cause failure or malfunction of the system.
Do not use in an atmosphere having corrosive gases, chemicals, sea water, water, water steam, or where there is direct contact with any of these . 2. Do not use in an environment where flammable gas or explosive gas exists. Usage may cause a fire or explosion. The products do not have an explosion proof construction. 3. Do not use in a place subject to heavy vibration and/or shock. 4.