Air Cooled Aftercooler Series HAA 1

Model A B C A B C A B C A B C 500 1000 1500 1000 2200 3000 2000 3300 4000 4000 5700 7000 34.5 38 40 33 36.5 38 34 36 37 34 35 36 35 40 44 35.5 40 42 37 40 41.5 38 40 42 35.5 42.5 47.5 36 42.5 44 38.5 42.5 45 39 43 45 HAA7 HAA15 HAA22 Maintenance HAA37 Caution 1. Inspect the cooler at least once a week and clean it to prevent it from becoming obstructed. 2.

90

Flow Rate Characteristics Relief Characteristics IR3020-04-A Supply pressure: 0.7 MPa IR3020-04-A Back pressure: 0.7 MPa 0.7 0.7 0.6 0.6 Set pressure [MPa] Set pressure [MPa] 0.5 0.5 0.4 0.4 0.3 0.3 0.2 0.2 0.1 0.1 0 0 1000 2000 3000 4000 5000 6000 0 0 1000 2000 3000 4000 5000 Flow rate [L/min (ANR)] Flow rate [L/min (ANR)] Pressure Characteristics Supply pressure: 0.3 to 1.0 MPa Set pressure

AR Series Modular Type Regulator

1500 0 500 1000 1500 Flow rate L/min (ANR) Flow rate L/min (ANR) AR40-A Rc1/2 AR40-06-A Rc3/4 0.6 0.6 0.5 0.5 Outlet pressure (MPa) Outlet pressure (MPa) 0.4 0.4 0.3 0.3 0.2 0.2 0.1 0.1 0 0 1000 2000 3000 4000 0 0 1000 2000 3000 Flow rate L/min (ANR) Flow rate L/min (ANR) 452 Regulator AR10-A to AR40-A Series Pressure Characteristics (Representative values) Conditions: Inlet pressure 0.7

5 Port Solenoid Valve Series SV

0.5 0.6 0.7 0.8 0.9 1.0 200 CM2 20 50% 70% 10% 30% 150 Stroke mm AS2201F -01-06 AS2200-01 70% 100 50 10% 30% 50% 0 200 CM2 25 150 Stroke mm AS2201F -01-06 AS2200-01 100 50 0 ANA1 -C08 T0604 200 CM2 32 150 Stroke mm AS2201F -01-06 AS2200-01 100 50 0 200 CM2 40 150 Stroke mm AS2201F -02-06 AS2200-02 100 50 0 Solenoid valve Silencer Tubing Speed controller 200 300 400 500 600 700 800 900 1000

5 Port Solenoid Valve SY Series

Body ported Bore size Series CJ2 Pressure 0.5 MPa Load rate: 50% Stroke 60 mm Series CS1 Pressure 0.5 MPa Load rate: 50% Stroke 1000 mm 6 10 16 125 140 160 20 25 32 40 40 50 63 80 100 Series MB/CA2 Pressure 0.5 MPa Load rate: 50% Stroke 500 mm Series CM2 Pressure 0.5 MPa Load rate: 50% Stroke 300 mm Average speed (mm/s) Series 800 700 600 500 400 300 200 100 0 Perpendicular, upward actuation

DOT/J844 Nylon Tubing

Minimum Bending Radius (mm) 1/8 9.4 5/32 12.7 3/16 19.1 1/4 25.4 5/16 31.8 3/8 38.1 1/2 50.8 5/8 63.5 3/4 76.2 Minimum Burst Pressure (psi) at 24C (75F) 1000 1200 1200 1200 1000 1000 950 900 800 Material Nylon 12 (Polyamide) *Note: Recommended operating fluid and temperature range provides best performance and longest life.

Booster Regulator Series VBA1110 to 4200 1

Handle operated type Air operated type VBA1110 VBA200 VBA400 Model AV Max. 2 Pressure increase ratio VBA2200-03 VBA4200-04 VBA1110-02 VBA1-02 VBA2100-03 VBA4100-04 Note) 400 60 1000 1900 1000 1900 Max. flow (l/min (ANR)) VBA1 2 to 4 AU 1/2 (IN/OUT) 1/4 (IN/OUT) Connection port size Rc 3/8 (IN/OUT) 3/8 (IN/OUT) 1/2 (IN/OUT) Fluid Compressed air 1/4 Exhaust port size Rc 3/8 1/2 1/2 3/8 VBA1110

This is a legacy product. Please contact us for the latest version.sales@ocaire.com

ITVH

Right angle type cable connector 3 m 52 10 ARJ (33) Straight type cable connector 3 m AR425 to 935 52 12.5 ARX AMR Setting part ARM 10 M12 x 1 Cable connection thread (Plug type) 5.5 8 ARP 111 11 Digital pressure display IR-A M5 x 0.8 Solenoid valve EXH Breathing IR M4 x 0.7 depth 8 F.G.

CYV

Table 1 100 Total operation cycles (10,000) 50 40 30 20 10 100 200 300 400 500 700 1000 Stroke (mm) Inner cover holding screw tightening torques [Nm] Tightening torque Model Screw size CYV15 0.3 M3 x 0.5 CYV32 2.45 M6 x 1 Plate Stroke adjustment screw (inner cover) Hexagon wrench Inner cover holding screw direction + direction 11 SMC'S GLOBAL MANUFACTURING, DISTRIBUTION AND SERVICE NETWORK

VG342

Wiring 1) Pass them through the cable (7) in the order of cable ground (4), washer (5), rubber seal (6), and then insert into the housing (2). 2) From the terminal block (3), loosen the screw (11), then pass the lead wire (10) through, then again tighten the screw (11). Note) Tighten within the tightening torque of 0.5 Nm 15%. Note) Cable (7) external: 6 to 8 mm 3.

VT307

Wiring 1) Passing through the cable (7), cable gland (4), plain washer (5), rubber seal (6) in this order, and then insert into the housing (2). 2) From the terminal block (3), loosen the screw (11), then pass the lead wire (10) through, then again tighten the screw (11). Note 1) Tighten within the tightening torque of 0.5 Nm 15%.

VT317

Ground 4-7-11 12 Series VT317 How to Use DIN Terminal 1.

VPA4

Refer to pages 5-11-2 to 6 for Safety Instruction and Solenoid Valve Pilot pressure (MPa) Caution 1. Lubrication Use turbine oil Class 1 (ISO VG32). 2. Refer to Best Pneumatics Vol. 3 regarding piping, air quality, operating condition and 3 position closed center.

Dual Rod Cylinder/High Speed Specification Type Series CXS-XB19

bore depth 3.3 3 3 OUT 9 2-1.2 x 12l AW (spring pin) 1 (16) 5.6 3.2 28 0.2 28 0.2 22.7 37 35 16 6.3 5 2.1 M3 x 0.5 x 12.5l and M3 x 0.5 (hexagon bolt) (hexagon nut) 6 2-M3 x 0.5 (through) 2-M5 x 0.8 thread depth 4.5 (piping port) IN 7 2-M3 x 0.5 (through) 13 + ST 2-M5 x 0.8 thread depth 4.5 (piping port) (same on reverse side) 10 2-M3 x 0.5 thread depth 4.5 (same on reverse side) 4 8 6 11

Magnet Gripper Unit for Collaborative Robots

Function Explanation 1 NC 2 NC 3 Auto switch (For holding workpiece) 4 Auto switch (For releasing workpiece) 5 +24V Power supply for 24 VDC 6 Valve ON/OFF (For holding workpiece) 7 Valve ON/OFF (For releasing workpiece) 8 GND Power supply for 0 VDC M8 8 Pin connector (Socket) M8 8 Pin connector (Socket) 11 - 3-6.

VNC

1600 0.3 0.2 7 3 8 11 15 11 15 14 20 16 25 22 32 22 32 28 40 28 40 33 50 33 50 0.7 0.5 1 2 VC 3 4 1.0 0.8 VDW 1.4 1.2 1 VQ 1 4 1 2.4 2.2 VX2 5.2 5.0 32 VX Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com 1 2 1 3.8 3.6 VX3 7.0 6.8 40 JIS Symbol Valve type Operation

Ejector Valve Unit Series ZYY/ZYX 1

2 Aluminum Diffuser t Stainless steel Needle y Aluminum Spool u Resin Piston i 13-8-11 12 Series ZYY/ZYX Exhaust Characteristics/Flow Characteristics The flow rate characteristics correspond to a supply pressure of 0.45 MPa.

Gun Type Ionizer

(Rated voltage 125 V, Plug JIS C 8303, Inlet IEC 60320-C13) *1 Measured with a high pressure probe of 1000 M and 5 pF *2 Measurement value based on a charged plate (Dimensions: 150 mm x 150 mm, Capacitance: 20 pF) as defined in the U.S.

Bag Filter

NBR FGFS5-60 AL-27S 1 FGFC5-60 11 O-ring FGFL3-40 AL-23S 1 FGFR3-40 FKM FGFL5-60 AL-24S 1 FGFR5-60 FGFS3-40 3 FGFC3-40 AL-20S NBR FGFS5-60 5 FGFC5-60 12 Gasket FGFL3-40 3 FGFR3-40 FKM AL-21S FGFL5-60 5 FGFR5-60 Note 1) Refer to How to Order on page 47 for the part of the model number.