Polyurethane Coil Tubing Series TCU Do not make any modifications to be product. Do not take the product apart. Piping Caution 1. Before piping Make sure that all debris, cutting oil, dust, etc, are removed from the piping. 2. Wrapping of pipe tape When screwing piping or fittings into ports, ensure that chips from the pipe threads or sealing material do not get inside the piping.
(mm) 3.2 4 6 8 10 12 D Tubing I.D.
Safety Instructions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
Our pressure switches do not have an explosion proof rating. Never use it in the presence of an explosive gas as this may cause a serious explosion. Panel Caution Panel mounting adapter A Panel mounting adapter B 1. Do not use in an environment with spattering liquid of oil or solvent. 2.
Do not mount the product in locations where it is exposed to radiant heat. 5. Do not use in dusty locations or where water, oil, etc., splash on the equipment. 6.
Do not mount the product in locations where it is exposed to radiant heat. 5. Do not use in dusty locations or where water, oil, etc., splash on the equipment. 6.
7 9.5 12 There is no difference in the frequency and the inrush and energized apparent power because a rectifying circuit is used in the AC (Class B, Builtin full-wave rectifier type).
Fig. 12-1 Correct position Fig. 12-2 Incorrect position 25/28 8. Made to order product A wide range of made-to-order products are prepared depending on operating environment and conditions. Refer to Table 13 for made-to-order products.
Do not use valves where there is direct contact with, or in atmospheres of, corrosive gases, chemicals, salts water or steam. 2. Do not use in an explosive atmosphere. 3. Do not use in locations subject to vibration or impact. Confirm the specifications for each series. 4 - 4. A protective cover should be used to shield valves from direct sunlight. 5.
Do not use pressure sensors with corrosive and/or flammable gases. 7. The applicable fluids are air, non-corrosive gas and non-flammable gas. Consult with SMC if the switch is to be used with other types of fluids. Caution Connection Caution 1. Do not drop, bump, or apply excessive impacts (100 m/s2) while handling.
Name Alarm flag 1 Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Name Alarm flag 2 Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Name Alarm flag 3 Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Name Alarm flag 4 Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Name Alarm flag 5 Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Bit Name Explanation 0 Low tank fluid level 1 CH1 abnormal high circulating fluid temp. 2 Reservation
Front Mounting Rear Male Clevis, C Front Female Clevis, D Diameter E1 R W MF ZF FB CD EB L XD UB CB EW MR TR AO AT XA SA 32 48 32 16 10 130 7 10 65 12 142 45 26 26 9.5 32 10 4 144 142 40 55 36 20 10 145 9 12 75 15 160 52 28 28 12 36 11 4 163 161 50 68 45 25 12 155 9 12 80 15 170 60 32 32 12 45 12 5 175 170 63 80 50 25 12 170 9 16 90 20 190 70 40 40 16 50 12 5 190 185 80 100 63 30 16 190
Do not exceed the screw-in torque of 7 to 9 Nm when connecting the pipe to the switch. Exceeding these values may cause the switch to malfunction. 4. Do not use pressure sensors with corrosive and/or flammable gases or liquids. 5. Allow a sufficient margin of tube length in piping in order to prevent application of torsional, tensile or moment load to the tubes and fittings. 6.
(Page 11) 6 - 2) Avoid having a large gap between the clevis or trunnion and mating bushing, as this exposes the pin to a bending load. 3) Do not let foreign matter such as cutting chips get into the product from the suction port. 4) Do not touch the cylinder during high speed and high frequency operation.
Do not service or attempt to remove product and machinery/equipment until safety is confirmed. 3. Do not service or attempt to remove product and machine 3. Do not service or attempt to remove product and machine 3. Do not service or attempt to remove product and machine 3. Do not service or attempt to remove product and machine 3.
Plug) FAFB C + Stroke S A + Stroke x 2 (RA) MC E + Stroke B + Stroke Common Dimensions (mm) Slide DB Bore size (mm) Standard stroke (mm) B C DA FA FB G GA GB H J L MA MM ML NN HA E MT K MB A MC Ball bushing 12 16 20 25 32 40 50 63 6 6 8 8 8 8 9 9 8 8 10 10 12 12 16 16 26 30 36 42 48 54 64 78 19 19 30 30 38 38 60 60 5 5 6 6 10 10 12 12 51 58 68 82 100 108 139 153 8 8 10 10 12 12 16 16 18 22
When another part is mounted, tighten with the torque of 0.60.05 Nm. -23- 12.
There is a risk of injury. (3) Do not disassemble or modify the product. This may cause human injury and/or an accident. Please contact SMC for repair and maintenance of the product. (4) Do not wipe the product using chemicals.
Do not operate with the magnetic coupling out of position. If the magnetic coupling is out of position, push the external slider (or the piston slider by using air pressure) back to the proper position at the stroke end. (When pushing the external slider, do not push it with bare hands.) 4. Do not apply lubricant, as this is a non-lube product.
Do not disassemble the product. Products which have been disassembled cannot be guaranteed. If disassembly is necessary, please contact SMC. Operating Environment Warning 1. Do not use valves in atmospheres of corrosive gases, chemicals, salt water, water or steam, or where there is direct contact with same. 2. Do not use in explosive atmospheres. 3.