HRX-OM-X071 Here is an example showing these relationships.
An error code is returned if an instruction code outside the range set in parameter No.
An error code is returned if an instruction code outside the range set in parameter No.
Non-food zone An environment in which foods do not contact the cylinder: . 42 17.5. Do not use in an area where surges are generated: . 42 17.6. Installation . 43 17.7. Wiring (Including connecting/disconnecting of the connectors) . 44 17.8. Adjustment and Operation . 46 17.9. Washing . 47 18. Maintenance . 48 19.
Caution When using an exhaust cleaner, mount it downwards.
The test was performed in both an axial direction and a perpendicular direction to the lead screw.
Furthermore, it cannot be used as an emergency cutoff valve. Terminal deceleration and an intermediate speed change circuit can be produced easily. Universal porting could be used as a selector/divider valve. The simple system configuration permits sharp response. The large capacity system configuration without connection loss allows the use of smaller valves and piping.
Do not use in an environment with temperature cycles.
It converts air pressure to an equivalent hydraulic pressure, and this hydraulic pressure is used for operating an actuator, thus solving the problem that is associated with the compression characteristics of air.
System configuration Be sure to secure an air supply capacity of the minimum operating pressure (0.1 MPa) or more.
It converts air pressure to an equivalent hydraulic pressure, and this hydraulic pressure is used for operating an actuator, thus solving the problem that is associated with the compression characteristics of air.
A cabtire cable with an O.D. 6 to 12 mm is applicable. Tighten each part with an appropriate tightening torque shown below.
VVQ5000-25A1 5 Intermediate stop Drop prevention Can hold an intermediate cylinder position for an extended time. When combined with a double check spacer with built-in double check valve, it is unaffected by air leakage between the spool valves, making it possible to hold a cylinder at an intermediate stopping position for an extended time.
An application which could have negative effects on people, property, or animals requiring special safety analysis. 4. Use in an interlock circuit, which requires the provision of double interlock for possible failure by using a mechanical protective function, and periodical checks to confirm proper operation. 1.
As a guide, an acceptable tightening level is reached by tightening the screw an additional 90 degrees (1/4 turn) from the point at which the screw is snug. (Refer to Figure 3.)
Some fluids can deteriorate a seal or an O-ring, and have an affect on the filter function, causing leakage. The wetted parts of the pressure gauge is made of brass. Check the compatibility with fluid in use. EB ES 1. Failure to observe the procedure will likely cause fluid leakage or removal of a cover, which may lead to an unexpected accident.
Refer to page 100 for part numbers. 45 46 Non-standard Motor Series LJ1H10 Rolled Ball Screw High Rigidity Direct Acting Guide Motor Output 50W 12mm/12mm lead Horizontal Mount How to Order Stroke 1 LJ1H10 G NB 1 F W X10 Cable entry direction Top entry Left entry Power supply voltage Motor specification Cable entry direction Switch Matsushita Electric Industrial Co., Ltd.
Furthermore, by connecting an input block, a maximum 32 sensor signal inputs are possible. SI unit for AS-i As a AS-i slave unit, this kit is capable of up to 4 or 8 points of solenoid valve ON and OFF control. Furthermore, by connecting an inmput block, a maximun 4 or 8 sensor signal inputs are possible.
When removing drain is difficult, use of a filter with an auto drain is recommended. ITVX PVQ VY1 VBA VBAT AP100 3. Piping materials without flexibility such as steel tube piping are prone to be effected by excess moment load and vibration from the piping side. Use flexible tubing in between to avoid such an effect. Caution 1.
If the workpiece gripping point goes beyond the range limits, this will have an adverse effect on the life of the air gripper.