Electro-Pneumatic Positioner Series IP8000/8100 Series IP8000/8100 (Lever type) (Rotary type) 100mm in height (shortened by 13% compared with IP6100) 100mm in height (shortened by 13% compared with IP6100) 100mm in height (shortened by 13% compared with IP6100) Folk lever joints (Rotary type) Can absorb off-centering. 100mm 100mm Spring pin Pressure gauge (O.
To be provided by customer.) PLC Electric Actuator (Not incl. To be provided by customer.) Electric Actuator DIN rail mount With built-in positioning (pulse) output function Movement pattern can be directly specified by PLC. Controls positioning by pulse signals Reduces design requirements The driver can be controlled by general purpose positioning unit or controller.
MY3M Sum of guide load factors = Load mass [m] Static moment [M] Note 1) Dynamic moment [ME] Note 2) 1 + + Maximum allowable load [mmax] Allowable static moment [Mmax] Allowable dynamic moment [MEmax] Note 1) Moment caused by the load, etc., with cylinder in resting condition. Note 2) Moment caused by the impact load equivalent at the stroke end (at the time of impact with stopper).
Although the body of the switch may not be damaged, the inside of the switch could be damaged and malfunction. wDo not carry a cylinder by the auto switch lead wires. Never carry a cylinder by its lead wires.
Select the response time by pressing either button or button. ( : 2.5 ms, : 24 ms, : 192 ms, : 768 ms Select among them.) Select Auto preset mode or Manual set mode by pressing either button or button. Auto preset mode Manual set mode Manual Pressure Setting Output mode differs by the pressure set value. 1. Manual set mode 2. Input set point value for OUT1 (1) 3.
When using valves for water application in cold climates, take appropriate countermeasures to prevent the water from freezing in tubing after cutting the water supply from the pump, by draining the water, etc. When heating by steam, be careful not to expose the coil portion to steam.
Note 2) Since the table is made of a magnetic substance, it could become magnetized if touched by a magnet, etc.
This can be solved by closing the stop value 1 to 2 seconds later.
Measurement instruments that SMC manufactures or sells have not been qualified by type approval tests relevant to the metrology (measurement) laws of each country. Therefore, SMC products cannot be used for business or certification ordained by the metrology (measurement) laws of each country.
IDF IDU IDFA Effects of moisture on equipment IDFB IDFB Generation of water droplets Malfunctioning of valves and actuators caused by dripping grease Decomposition of auto drain caused by rusting inside pipes IDH ID IDG IDK AMG R134a(HFC), R407C(HFC) Coefficient of destruction for ozone is zero.
Fittings & Tubing Air Cylinders Rotary Actuators How to Use DIN Terminal Surge Voltage Suppressor
It is possible to identify the product when multiple controllers are mounted and identify the flow direction by attaching an identification label.
The descriptions of products shown in this document may be used by the other companies as their trademarks. 2021-2023 SMC Corporation All Rights Reserved No.EX-OMY0032-B
The descriptions for OUT2 are the same as those for OUT1, under the conditions that [n_1] and [n_2] should be replaced by [n_3] and [n_4], [P_1] and [P_2] should be replaced by [P_3] and [P_4] and [H_1] should be replaced by [H_2]. Input a set value for pressure to perform switch output.
AWM Micromist can be constantly supplied by merely adjusting the mist generating pressure differential.
Simple and unencumbered appearance by adopting round-shaped cord.
If the manual override is turned by 180 counterclockwise and mark is adjusted to 0, locking will be released and the manual override will return.
Note 2) On the AMC220, an R 1/4 fittinng can be attached by removing the drain cock. (It be comes the drain piping type.
Turn another 90 from the position where tightening is felt by hand.