2/3 Port Valve Option Symbol and Configuration Fluid and Options Option symbol Seal material Coil insulation Body, Shading coil material Option symbol and body material Brass SUS304 F L X F, B L, J B J B J J T A H A H A H D N G, J S Q E P V M Y A H K K A H A H B J V M V M Y D, E N, P B J Fluid(Application) Standard A B C D E F NBR FPM Argon Argon(long life) Ethyl Alcohol Ethylene glycol Ozone(low
Mineral oil A C A A A A 18 Sodium hypochlorite (2%, Room temperature) A C A D D B 19 Sodium chloride A A A A B 20 Carbon dioxide A A A A A A 21 Natural gas A A A A A A 22 Boric acid A B A D A B 23 Unless noted otherwise, the solution concentration is in a saturated state.
1 1 1 1 2 (a) (a) (b) (c) (a) (b) (c) (b) (c) (a) (b) (c) (a) (b) (c) (b) (c) (a) (b) (c) (b) (c) (a) (b) (c) Note 1) The above (a), (b), (c) indicate heater mounting positions.
(A contact) N.O. (A contact) Number of auto switches N.O. (A contact) N.O. (A contact) 1 2 1 pc. 2 pcs. 6 6 pcs.
In the case of 0.8MPa, when port A is a vacuum, port P can be pressurized to 0.8MPa (7kgf/cmG).
Stabilize the source pressure by providing a tank and a vacuum regulator. Provide a vacuum switch valve to individual lines.
A G i 2 x P Port size G A 2 x P Port size b B Conduit DIN terminal D F Q S Cable 6 to 12 G1/2 F Q 280 D G1/2 45 (42) (44) 31.5 Built-in full-wave rectifier type R C C R E J J E 2 x M depth 5 H 2 x M depth 5 B B1 H G A G A B B1 2 x P Port size 2 x P Port size Bracket mounting hole a1 (VXS23, 25) a a1 (VXS24, 26) 6.5 10.5 Dimensions (mm) Model Port size P A B B1 C D E F G H J M Bracket mounting
ARP VY1D00 VY1400 IR-A Simple circuit configuration IR 1 Piping labor reduced A flexible system has been adopted.
Therefore, internal parts of a cylinder other than rod seal are not replaceable. 2. Use caution to the popping of a retaining ring. When replacing rod seals and removing and mounting a retaining ring, use a proper tool (Retaining ring plier: Tool for installing a type C retaining ring).
A A A-A r q e w A A-A e r q w Component Parts No.
Use the table below as a guide when adjusting auto switch positions, etc.
Use the table below as a guide when adjusting auto switch positions, etc.
or less 0.5 A or less 0.5 A or less Power supply fuse 3 A 1 A 1 A Two-time Hitting Function Interrupt Operation Function A two-time hitting function has been adopted to improve the bag filter dusting efficiency.
Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Caution: Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Warning: Danger : Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury.
Once in the mounting position, use a flat head watchmakers screwdriver to tighten the included set screw. Note) When tightening the set screw, use a watchmakers' screwdriver with a handle diameter of about 5 to 6 mm.
Front matter 5 14 (4) Test method By attaching the equipment for testing with the test circuit shown in Fig. (3) and running water at 5 to 40C, measure the flow rate with a pressure difference of 0.075 MPa. However, the pressure difference needs to be set with a large enough difference so that the Reynolds number does not go below a range of 4 x 104.