JIS Standard Hydraulic Cylinder Note 1) To protect auto switches, ensure that main body of an auto switch should be embedded into auto switch mounting groove with a depth of 15 mm or more. Note 2) Set the tightening torque of a hexagon socket head set screw (M4) to be 1 to 1.2 Nm. Note 3) When tightening an auto switch mounting screw (M2.5), use a watchmakers screwdriver with a grip diameter of 5 to 6 mm.
For installation and removal, use an appropriate pair of pliers (tool for installing a type C snap ring).
Note Bracket A ZS-46-A1 Tapping screw: Nominal size 3 x 8 L (2 pcs.) Bracket B ZS-46-A2 Tapping screw: Nominal size 3 x 8 L (2 pcs.)
A A A A SS5Y5-45S1UStations D.
An auto switch for detecting the location can be mounted. 10D MHZ2-16D 20D 10DN MHZ2-16DN 20DN Tool stand Added to the standard tool adapter The height for setting a tool can be adjusted. An auto switch for detecting a tool can be mounted.
46 119.2 58 136 173 MORE DIMENSIONS S E E N E X T P A G E Courtesy of Steven Engineering, Inc. !
when the gripper was tested with a drop tester in both an axial direction and a perpendicular direction to the lead screw.
The cushion effect (smooth start-up, soft stop) cannot be obtained in an intermediate stop or a return from an intermediate stop using an external stopper, etc.
Note 6) A reference value for correcting an error in reciprocal operation. Note 7) Impact resistance: No malfunction occurred when the actuator was tested with a drop tester in both an axial direction and a perpendicular direction to the lead screw. (Test was performed with the actuator in the initial state.)
of a command is not normal. 3.12 Negative response HRS400-A-46 3-16 DOC1003626 Chapter 3 Serial communication Communication example Device Address: No.1 Read seven consecutive data from register 0100h which is out of range.
Do not use the actuator in an environment where there is possible danger of corrosion. 2. Install a protective cover on the entire product in an environment where a large amount of dust is present or where the product is exposed to water or oil drops. 3. Do not use the actuator in an environment where a strong magnetic field is present. Maintenance Warning 1.
To ensure a permanent path. Stable operation is possible even with an eccentric load, through the use of a ball bushing. When smoother operation is required even with an eccentric load. Auto switches can be mounted. Impact at the stroke end is absorbed by inclusion of a shock absorber. The use of a linear guide makes possible a large load, large moment and high precision.
Note 1) To protect auto switches, ensure that main body of an auto switch should be embedded into auto switch mounting groove with a depth of 15 mm or more. Note 2) Set the tightening torque of a hexagon socket head set screw (M4) to be 1 to 1.2 Nm. Note 3) When tightening an auto switch mounting screw (M2.5), use a watchmakers screwdriver with a grip diameter of 5 to 6 mm.
an intermediate stop of a load using an air pressure circuit, operate at or below the kinetic energy shown in the table below.
Series KS Blue Series KX Blue Slide bearing Smooth operation and longer life from an oil containing slide bearing. Rotary seal A special rotary seal minimizes friction while providing an excellent seal.
A water-resistant type cylinder is recommended for use in an environment which requires water resistance.
The cushion effect (smooth start-up, soft stop) cannot be obtained in an intermediate stop or a return from an intermediate stop using an external stopper, etc.
Since the stroke absorption of rubber bumpers is short, when adjusting the stroke with an A unit, install an external shock absorber.
The cushion effect (smooth start-up, soft stop) cannot be obtained in an intermediate stop or a return from an intermediate stop using an external stopper, etc.
When it is necessary to operate it as an ordinary double acting cylinder at an even lower operating speeds, use a low speed cylinder (refer to Made to Order on page 6-17-19).