Table of Contents Dedicated grounding should be used as much as possible. Grounding should be to a type 3 ground. (Ground resistance of 100 or less.) 3. Use a wire with a sectional area of 2 mm2 or larger for grounding. Grounding should be as close as possible to the controller, and the ground wires should be as short as possible. 4.
If the chewed portion of the tubing is used as is, this can cause trouble such as air leakage or difficulty in removing the tubing. 2. When mounting a One-touch fitting, use a suitable wrench to tighten the hexagonal flats of the fitting. Moreover, position the wrench at the lower part of the hexagonal flats as close to the threads as possible.
E/40M E L 50 mm Handling Precautions * When used as a stopper, select a model with a stroke of 30 mm or less. * LEYGLE (ball bushing bearing) cannot be used as a stopper. * Workpiece collision in series with guide rod cannot be permitted (Fig. a). * The body should not be mounted on the end.
large load and a high speed, as the piston comes to a stop at the stroke end.
When used as a stopper, select the LEYG series Sliding bearing for a stroke of 30 mm or less. 4. When used as a stopper, fix the main body with a guide attachment (Top mounting or Bottom mounting). If the end of the actuator is used to fix the main body (end mounting), the excessive load acts on the actuator, which adversely affects the operation and life of the product. 9.
When a load, such as a relay or solenoid, which generates surge is directly driven, use a type of switch with a built-in surge absorbing element. 8. Cautions for use in an interlock circuit.
This product operates as a device. It does not send any requests.
(A, B port) Applicable tubing O.D.: 6,1/4" 24.5 1/8 (A, B port) Other dimensions are the same as the grommet type.
Wiring should be kept as short as possible.
Note 3) When tightening an auto switch mounting screw (M2.5), use a watchmakers screwdriver with a grip diameter of 5 to 6 mm. Also, set the tightening torque to be 0.05 to 0.15 Nm. As a guide, turn 90 from the position where it comes to feel tight.
back flow mechanism as a standard feature.
How to Order Type 46 (5 port/Base mounted) 10 SS5YJ3 46 05 M5 Type 46 Type S46 ( ) Single solenoid pilot valve is on same side as the A, B port. Clean series CE-compliant M5 x 0.8 R1, R2 port Stations Nil 02 2 stations Valve mounting direction P port thread type Q CE-compliant : : Single solenoid pilot valve is on opposite side as the A, B port.
Combination description Holder mounting bracket X416 1 2 1 1 1 1 1 1 1 X417 1 1 1 1 1 2 1 1 1 Nil W Z A L H AZ LZ HZ Nil W A L H A, L, H, AS, LS, HS A, L, H AL, AH AL, LH AH, LH AL, AH AL, LH AH, LH A, L, H, AS, LS, HS A, L, H AL, AH AL, LH AH, LH X416 on one side X416 on both sides X416 on one side, X417 on the other side X416 on A unit side X416 on L unit side X416 on H unit side
It cannot be mounted at a later time or used as a separate unit.
Use caution, as operation at a pressure exceeding these limits can result in breaking of the magnetic coupling.
The U-shaped groove is machined into the cushion ring in such a way that this acceleration process can proceed smoothly (as a sine function).
The U-shaped groove is machined into the cushion ring in such a way that this acceleration process can proceed smoothly (as a sine function).
When using as a stopper, select a model with 50 stroke or less.
(A contact) N.O. (A contact) Specifications N.O. (A contact) N.O.