Direct Operated 2 Port Solenoid Valve For Water, Oil, Steam, Air Series VX21/22/23 1 Be particularly careful in determining the compatibility with the fluid to be used. 2. Only trained personnel should operate machinery and equipment. The fluid can be dangerous if handled incorrectly. Assembly, handling or maintenance of the system should be performed by trained and experienced operators. 3.
If the initial pressure drop is set to be high, its service life will be shorten due to clogging. 2) TSJ connection The TSJ fitting is a kind of a self-align fittings. Set it as shown in the figure.
Note) : Can be used at low temperatures and low concentration.
be adjusted with a flat head screw driver Prevents inadvertant manual operation SMC Pneumatics, Inc.
While the gap is widened, dust and foreign particles caught between plates can be washed away by back flushing the element. This restores the element and enables repeated use of the element. The gaps between filter plates are equally maintained by the wave washers to allow stable back-flush operation. 2 types of elements are available according to the type of dust.
Note) : Can be used at low temperatures and low concentration.
Type: 000 (Lever Type Feedback), Pressure Gauge: 0 (None), Construction: 1 (w/Terminal Box), Accessories: E (For Stroke 35 to 100mm w/Lever Unit), Connection: 4 (G1/4, G1/2)
Type: 000 (Lever Type Feedback), Pressure Gauge: 3 (1.0MPa), Construction: 1 (w/Terminal Box), Accessories: BE (B+E), Connection: 1 (1/4NPT, G1/2)
Type: Lever Type Feedback, Pressure Gauge: 1.0MPa, Construction: w/Terminal Box, Accessories: B+E, Connection: 1/4NPT, G1/2
When the Local User Interface is locked the lock symbol will be activated on the display. 5.6.4 Linearization Linearization FLI can be used for linear valves when linkage geometry is needed to be corrected by valve controller.
Set parameter No.PA08 001. Afterwards, do 1 and 2 alternately. 1. Reduce value of parameter No.PA09 to be less than present value. 2. Operate and ascertain the situation. The gain is adjusted automatically. For LECSB(Pulse input), LECSC/LECSC-T(CC-Link), LECSS(SSCNETIII) A. Adaptive filter II Set parameter No.PB01 0001 and drive the motor. The filter is adjusted automatically. B.
Reuse 1) Normally, fittings with a sealant can be reused up to 6 to 10 times. 2) The seal ring cannot be replaced.
't E E Criteria of Accelerating Speed (Vertical Orientation) LXSH2SA LXSHSSA LXSH2BC LXSH5BC : : . : : ; ; l t , , , , . ' , , r , , , . ' , , , L L 001 0'D2 003 L .rime G) 0.0r a.a2 0 03 LXSH2BD \ ; i A,Caution Pay Joad should be undet the maxjmum pay Joad.
Be sure to connect the pipe to the fluid release port so that fluid releasing work can be absolutely performed. 7. Pipe so that air releasing work can be absolutely performed. The air releasing work can be done firmly if you make the piping in order to flow a small flow constantly into a tank by resin tubing, etc. from the air release valve. (Refer to Fig. 2.)
Therefore, the acceleration rate of the lateral movement must be minimized. Use the magnet gripper for horizontal handling. Adequate safety factor needs to be considered for Moving direction inclined handling or vertical Thin workpieces may be deformed during transportation. It is recommended to use multiple magnet grippers for scenarios such as this.
If multi-pads are used with only one ejector and one pad does not make complete adsorption, then vacuum pressure will be lost. Subsequently other pads will be unable to complete adsorption.
The mounting bracket Itself will be .. Mour"lbng is the same as standard EI~ types.
The right side of the common port provides plug. 17-3-107 8 The VX series will be revised shortly.
Actuation Warning 1 Normally closed qCannot be used for vacuum retention. wUse a release valve. (Without a release valve, the work piece may not be released.)